Report No: ACS19044 WEST BANK & GAZA ENERGY EFFICIENCY ACTION PLAN 2020-2030 Final Report June 2016 Energy Efficiency Action Plan for 2020-2030 – Final Report Standard Disclaimer: This volume is a product of the staff of the International Bank for Reconstruction and Development/ The World Bank. The findings, interpretations, and conclusions expressed in this paper do not necessarily reflect the views of the Executive Directors of The World Bank or the governments they represent. The World Bank does not guarantee the accuracy of the data included in this work. The boundaries, colors, denominations, and other information shown on any map in this work do not imply any judgment on the part of The World Bank concerning the legal status of any territory or the endorsement or acceptance of such boundaries. Copyright Statement The material in this publication is copyrighted. Copying and/or transmitting portions or all of this work without permission may be a violation of applicable law. The International Bank for Reconstruction and Development/ The World Bank encourages dissemination of its work and will normally grant permission to reproduce portions of the work promptly. For permission to photocopy or reprint any part of this work, please send a request with complete information to the Copyright Clearance Center, Inc., 222 Rosewood Drive, Danvers, MA 01923, USA, telephone 978-750-8400, fax 978-750-4470, http://www.copyright.com/. All other queries on rights and licenses, including subsidiary rights, should be addressed to the Office of the Publisher, The World Bank, 1818 H Street NW, Washington, DC 20433, USA, fax 202-522- 2422, e-mail pubrights@worldbank.org. 2 Energy Efficiency Action Plan for 2020-2030 – Final Report TABLE OF CONTENTS Abbreviations and acronyms....................................................................................................... 5 1. Executive summary ...................................................................................................... 6 1.1. Methodology ..................................................................................................... 6 1.2. Review of the Palestinian energy sector ........................................................... 6 1.3. Demand forecast by usage and Energy Efficiency target ................................. 7 1.4. NEEAP 2020-2030 ........................................................................................... 7 2. Introduction and methodology ...................................................................................... 9 2.1. Introduction ....................................................................................................... 9 2.2. Methodology ..................................................................................................... 9 3. Energy and EE market review and diagnostic ............................................................ 12 3.1. Key general indicators .................................................................................... 12 3.2. Primary energy supply and consumption ........................................................ 16 3.3. Electricity sector ............................................................................................. 20 3.3.1. Description of the value chain ............................................................ 20 3.3.2. Electricity usages ................................................................................ 22 3.3.3. Transmission and distribution losses .................................................. 23 3.3.4. Electricity tariffs.................................................................................. 24 3.3.5. Demand forecasting for electricity ...................................................... 27 3.4. Existing EE programs and preliminary results ............................................... 28 3.4.1. Targets defined by the National Energy Efficiency Action plan for 2012-2020 ............................................................................................................. 28 3.4.2. Review of the Phase I action plan results (2012 – 2014) .................... 30 3.5. Legal framework and key EE players ............................................................. 31 3.5.1. Overview of existing energy regulation .............................................. 31 3.5.2. Presentation of main existing key players ........................................... 31 4. Forecasted demand of electricity for 2020-2030 timeframe ....................................... 33 4.1. Methodology and main assumptions .............................................................. 33 4.2. Segmentation of the consumption of electricity by economic activity ........... 35 4.3. Segmentation of the usages of electricity ....................................................... 36 4.3.1. Industrial, commercial and service sectors ......................................... 39 4.3.2. Residential sector ................................................................................ 40 4.4. Forecasted demand by usage and potential savings ........................................ 43 5. 2030 Energy Efficiency targets .................................................................................. 47 3 Energy Efficiency Action Plan for 2020-2030 – Final Report 5.1. Reduction of consumption of electricity ......................................................... 47 5.2. Reduction of the CO2 emissions ..................................................................... 47 6. Review of key contributing technologies during 2020-2030 ..................................... 49 6.1. Lighting ........................................................................................................... 49 6.2. Electric motors ................................................................................................ 50 6.3. Room heating and air conditioning ................................................................. 50 6.4. Fridges (residential sector) .............................................................................. 51 6.5. Water heating .................................................................................................. 51 6.6. Smart homes.................................................................................................... 51 6.7. Building renovation and nearly Zero Energy Buildings ................................. 51 6.8. Smart metering ................................................................................................ 51 6.9. Smart grids ...................................................................................................... 52 6.10. Miscellaneous ................................................................................................. 52 7. Energy Efficiency Action plan for 2020-2030 ........................................................... 53 7.1. Global strategy and main assumptions ........................................................... 53 7.2. NEEAP 2020-2030 Phase I (Residential sector) ............................................ 55 7.3. NEEAP 2020-2030 Phase I (other sectors) ..................................................... 60 7.4. NEEAP 2020-2030 Phase II ........................................................................... 61 7.5. NEEAP 2020-2030 Phase III .......................................................................... 62 7.6. Impacts of this EE action plan on the creation of jobs ................................... 62 7.7. Recommendations for an implementation plan .............................................. 63 8. Conclusion .................................................................................................................. 65 9. References ................................................................................................................... 67 4 Energy Efficiency Action Plan for 2020-2030 – Final Report ABBREVIATIONS AND ACRONYMS CFL Compact Fluorescent Light CBA Cost Benefit Analysis DISCo Distribution Company EE Energy Efficiency ESCO Energy Service COmpany GDP Gross Domestic Product GEDCO Gas Electricity Distribution Company GHG Greenhouse Gas GPP Gaza Power Plant GWh Gigawatt hour HEPCO Hebron Electric Power Company HH Household HV High Voltage HVAC Heating, Ventilation and Air Conditioning IEC Israel Electricity Company Ltd JDECO Jerusalem District Electricity Company LED Light Emitting Diodes LPG Liquefied Petroleum Gas MENA Middle East and North Africa MEPS Minimum Energy Performance Standard MV Medium Voltage MWh Megawatt hour NEEAP National Energy Efficiency Action Plan NEDCO Northern Electric Distribution Company NIS New Israeli Shekel (1 USD ~ 3.69 NIS) NGO Non-Governmental Organization nZEB nearly Zero Energy Building PCBS Palestinian Central Bureau of Statistics PEA Palestinian Energy Authority PEC Palestinian Energy and Environment Research Center PERC Palestinian Energy Regulatory Council PF Power Factor PENRA Palestinian Energy and Natural Resources Authority PMA Palestinian Monetary Authority PPA Power Purchase Agreement PV Photovoltaic RES Renewable Energy Sources SELCO Southern Electric Company SME Small and Medium Enterprise TJ terajoule (1012 joules) 5 Energy Efficiency Action Plan for 2020-2030 – Final Report 1. EXECUTIVE SUMMARY The World Bank in partnership with PENRA, and in collaboration with the Agence Française de Développement (AFD) prepared this Energy Efficiency Action Plan for 2020-2030 (also referred to as NEEAP II) as a prolongation of the current plan for 2012-2020. Based on the lessons learned and PENRA’s vision of the sector, the NEEAP II introduces more ambitious energy efficiency targets. To be achieved, the implementation of NEEAP II should start before 2020 in order to provide results early next decade. The NEEAP II plan focuses on electricity since this form of energy has the largest share in the Palestinian final energy mix. The plan is also concentrated on a reduction of the consumption and not on the development of the renewable energy such as wind, biomass or solar PV. The potential for developing these renewable energies has already been addressed in another study led by PENRA. 1.1. Methodology The methodology used to build this Energy Efficiency (EE) Action Plan is based on an iterative cycle where EE actions are analysed in terms of benefits (reduction of the consumption) and costs (investment needed to implement technology replacements and consumer behaviour changes). These benefits and costs are then compared to an EE target for expected savings. Cumulated costs are compared with a given budget so that a selection of the more effective actions may be decided within this financial envelop. Another principle has been adopted: focus on the largest uses of electricity. National statistics are traditionally based on consumption by sector. In Palestine, the residential sector is the main consumer of electricity with more than 60% of the total consumption. In order to identify pertinent actions, we need to know the consumption by usage. For instance, in the industry sector, main usages are motors or heating/chilling. In the residential sector, the usages of electricity have been identified through surveys. An average consumption profile has been modelled to reflect the various usages of electricity by sector. Since this EE Action Plan is for the 2020-2030 timeframe, demand forecasts will help to size the potential reduction of the consumption. Usually, the EE target is a reduction of the present level of consumption at a given date1. Because of the particular situation of Palestine where energy consumption is already strongly limited by imports, it has been proposed instead to reduce the consumption growth rate during 2020-2030, compared to a “business as usual” scenario where no EE action would be implemented. The last component of the methodology is a review of the technologies that should reduce future consumption. For instance, lighting based on LED should divide by ten the consumption of incandescent bulbs. 1.2. Review of the Palestinian energy sector Palestine has the third fastest growing population (+2.9% per annum) in MENA during the last decade. Palestine has the lowest GDP but the highest economic growth rate. The fast-growing economy should positively influence future investments in EE actions for the industrial and commercial (I&C) sectors. Among MENA countries, Palestine ranks first in primary energy intensity2, which indicates a relatively low consumption of energy and as a consequence, a possible difficulty for reducing this consumption through EE actions in the residential sector. This is particularly true for Gaza where suppressed demand reaches a very high level. 1 In Europe, the target for 2020 is a reduction of 20% of the consumption below the 1990 level. 2 Ratio between total energy consumption and GDP. It is a measure of the total amount of energy required to generate a unit of GDP. 6 Energy Efficiency Action Plan for 2020-2030 – Final Report However, there should be room from improvement on Palestinian households. With 34%, electricity has the largest part of the Palestinian energy mix. Furthermore, the residential sector accounts for 60% of the consumption. This shows that concentrating EE actions on the residential sector should have a large impact on final consumption. Palestine is the MENA country with the highest use of Solar Water Heaters (SWH). 56% of households have a SWH system on their roof. However, one third of these systems is out of order. Moreover, distribution losses (technical and non-technical) reach a very high level (20-30%). A significant reduction of these losses would be of paramount importance for the nation. The price of electricity, based on IEC retail tariff, is very high in Palestine. As a consequence, the share of electricity in Palestinian household expenditures (9%) is the highest within MENA countries. Any EE action reducing consumption should have a short return on investment. However, for selecting the most appropriate actions, one needs to know what the future consumption will be during 2020-2030 and, if possible, by usage of electricity. 1.3. Demand forecast by usage and Energy Efficiency target A specific methodology for demand forecast has been developed to take into account specific evolutions for the residential sector (growth rate estimation: 2.2-2.4%/y) and the economic sectors (4.5%/y). Segmentation by usage is required to target the EE actions where substantial benefits are expected. The search for low hanging fruits leads to build a consumption profile. Electricity meters give a consumption which is the sum of all usages. Through the household surveys done by the Palestinian Central Bureau of Statistics (PCBS) it has been possible to identify the number of appliances per households and then to approximate the daily consumption by usage. Energy audits give similar information for the economic sectors. It seems that, for the residential sector, the main usages of electricity are air-conditioned, electric room heaters, water heating, fridge and lighting. A review of new technologies for these usages helps to identify specific actions such as the replacement of appliances or the switch to gas (LPG or NG) for heating. The NEEAP target for 2012-2020 is a reduction of the total consumption of electricity by 384 GWh during the 9-year period. The new proposed target in the NEEAP II for 2020-2030 is 5,000 GWh (or 500 GWh per year). However, the actions which are proposed in this new plan might lead to save up to 11,000 GWh if they were all implemented. This will provide flexibility to the Palestinian Authority to select some of the proposed measures according to budget or other constraints. How the prove the 2030 target is reached? Since the proposed target is related to the demand forecasts, there is a risk to over or under estimate the consumption without NEEAP (business as usual). To avoid this situation, indicators have been proposed for each individual EE action. The implementation of the proposed plan should save 3.5 million tons of CO2 each year. 1.4. NEEAP II 2020-2030 The proposed NEEAP II plan is built on three layers or phases: - The first layer or Phase I (2020-2030) is a follow up of the previous plan. It focuses mainly on the use of efficient appliances and industrial equipment. The information of the consumers and energy audits for the I&C sectors should help to replace inefficient energy-using products. The general deployment of smart meters is required to inform both households and distribution companies. The reduction of the grid losses (technical and non-technical) will be then easier to implement. The switch to gas for heating water is also an important action to decide as long as generation capacity is not enough to satisfy the demand. 7 Energy Efficiency Action Plan for 2020-2030 – Final Report - The second layer or Phase II (2024-2030) focuses on energy market structuring. The objective is to introduce demand side management. If the previous phase aims at reducing energy consumption (kWh), this second phase has in view a reduction of the peak load (kW). This is an important factor to take into account especially if a large proportion of (intermittent) renewable energy is integrated with solar and wind. - The third layer or Phase III (2027-2030) is dedicated to the use of new technologies such as smart homes, smart buildings and smart grids. The direct communication established between generation and consumption should optimize the use of infrastructures. A Time of Use Tariff (ToU) will then be required. The EE target which is proposed takes into account the benefits of the first layer (Phase I) only. A cost-benefit analysis has been provided for each action. The expected energy savings are then compared with the implementation costs. For each EE action, this provides a cost (US$) per kWh saved. When this ratio is less than the price of electricity, there will be positive return on investment. A summary of all the actions which are proposed is given by the table below. Energy Efficiency actions Benefits Total costs C/B (GWh) (US$ (US$/kWh) million) Lighting: move to CFL standard 2,612 1.750 0.001 Lighting: move to LED standard 322 2.275 0.007 Introduction of more efficient fridges 127 4.375 0.035 Switch to gas for room heating 246 24.832 0.101 Electronic thermostats 222 10.177 0.046 Labelling and national campaign 1,270 3 0.002 Repairing of SWH 1,576 126 0.080 Smart metering for all households 1,587 48 0.038 Submetering 317 4.812 0.015 Building thermal insulation 720 345 0.479 Labelling program 881 50 0.057 The only EE action which cannot be financially justified with the 10 year period of this plan is the thermal insulation of existing buildings. As a consequence, the action might be limited to the new constructions through the definition of a specific building code. In many countries, the implementation of EE action plans leads to create new jobs. For Palestine, several business opportunities could be created:  The local manufacturing of efficient lighting (CFLs and LEDs)  Repairing and installation / maintenance of new Solar Water Heaters  Energy audits for I&C sectors  Building thermal insulation To sum up, the Energy Efficiency Action Plan for 2020-2030 for Palestine puts forward additional opportunities for energy efficiency to reach an ambitious target to reduce total electricity consumption by 500 MWh per year. The Action Plan focuses on measures to reduce the consumption of electricity in the residential sector (two thirds of the national consumption) because of its largest savings potential. 8 Energy Efficiency Action Plan for 2020-2030 – Final Report Indeed, electricity is the main source of energy in the Palestinian energy mix, and for this source, the residential sector is the main consumer. Other energy sources have their own leading consumption sector. Diesel and gasoline are mainly consumed by the transport sector, LPG by the residential sector. These sources might need also a specific EE action plan. 2. INTRODUCTION AND METHODOLOGY 2.1. Introduction The Palestinian Energy and Natural Resources Authority (PENRA) currently oversees the implementation of the National Energy Efficiency Action Plan (NEEAP) for the period 2012 to 2020, which is divided in three phases. Phase I has been successfully achieved and Phase II is being implemented satisfactorily. The World Bank in partnership with PENRA, and in collaboration with the Agence Française de Développement (AFD) prepared this Energy Efficiency Action Plan for 2020-2030 (also referred to as NEEAP II) as a prolongation of the current plan. Based on the lessons learned and PENRA’s vision of the sector, the NEEAP II introduces more ambitious energy efficiency targets. To be achieved, the implementation of NEEAP II should start before 2020 in order to provide results early next decade. Similar to the current plan, the NEEAP II mainly focuses on electricity since this form of energy has the largest share in the Palestinian final energy mix. However, diesel3 is the second most used form of energy and should be considered in a future study. Benchmarking with other MENA countries has been introduced whenever possible in order to identify areas where Palestine is already well-advanced and others where potential progress could be achieved. 2.2. Methodology The methodology used in this draft NEEAP II encompasses the following five steps: 1. Demand forecasting: It is of paramount importance to know how final consumption of energy will evolve to sustain the economic development of the country. When a country, and this is the case for Palestine, is highly dependent on imports to satisfy the internal demand for energy, it is vital to monitor the costs for purchasing primary energy. Energy efficiency actions are mandatory when a cost reduction is targeted without neither impacting the economic development nor reducing the quality of life of the population. 2. Segmentation of energy demand: The main objective is to identify the volume of consumption per segment and potential savings. Several questions would need to be answered: Who are the consumers? What are their equipment and appliances? What are their behaviours? What is the energy efficiency potential for Palestine? The priority will be given to the “low-hanging fruits”, i.e. a small action over a large volume. The use of alternative sources of energy (wind, photovoltaic, biomass …) is not considered since these sources contribute to produce electricity and not to reduce the demand. However, solar thermal energy (e.g. for solar water heating) has to be considered since it reduces the consumption of electricity when used for electric heaters. 3 From an economical perspective, electricity is mainly used by the residential sector (more than 60%) whereas diesel is used almost exclusively by the transport sector. 9 Energy Efficiency Action Plan for 2020-2030 – Final Report 3. Review of electrical equipment technologies: The objective is to encourage the purchase and the use of highly efficient products. This is quite obvious for existing products. In the future, more efficient technologies or processes may become mature and affordable. In the case of lighting, for example, traditional bulbs -Edison’s invention one century ago- have been progressively replaced with CFLs (Compact Fluorescent Lamps) because their consumption is only 20% of the bulbs, which in turn are being replaced with LED (Light Emitting Diodes) consuming two or three time less and then, the introduction of infra-red detectors to switch off when nobody is present in the room. The price of these new appliances is generally higher than standard off-the-shelf products but, it is decreasing due to economies of scale. The key point is to determine when this price is justified by the savings and when it becomes affordable for a large number of customers. 4. Establish an energy saving target: Generally this target is expressed as a percentage of the total consumption for a given milestone or as a reduction of the forecasted growth rate of the demand. NEEAP 2010-2020 set the target for this period as a reduction of 383 GWh of the demand (~1% per year, compared to 2010 electricity consumption level). 5. Identify required Energy Efficiency actions: The objective is to identify the most cost- effective actions to reduce the forecasted consumption and reach the target. Because of the segmentation of the usages and the selection of appropriate technologies, it will be possible to recommend new products, the replacement of pieces of equipment, etc. To ensure the cost- effectiveness of each proposed action, a cost-benefit analysis is performed. Also, indicators are defined for each action so that an objective measure of the results can be done during and after implementation. The flow-chart below illustrates the methodology for drafting the NEEAP II. Since an investment needs to occur before obtaining any savings, it is helpful to compare the implementation costs with a given cost limit. When a new EE action is added to the proposed NEEAP II, the corresponding additional cost is compared with the cost limit. An iterative mechanism is then used to adjust the Action Plan so that the target can be reached within the cost limit. If this is not possible, either the target or the cost limit shall be revised. 10 Energy Efficiency Action Plan for 2020-2030 – Final Report In order to decide what the “best” technologies are, the technical review is not sufficient. It should be complemented with a cost - benefit analysis to estimate the benefits for the end user or client of energy services but also the investment costs. That is the reason why the section 6 proposes, for each energy efficiency action, an evaluation of the ratio cost/benefit per kWh saved. When this ratio is less than the actual cost of electricity, there a clear interest in implementing the corresponding EE action. 11 Energy Efficiency Action Plan for 2020-2030 – Final Report 3. ENERGY AND EE MARKET REVIEW AND DIAGNOSTIC 3.1. Key general indicators Palestine is composed of two territories, the West Bank and the Gaza Strip, which have different characteristics: population growth rate, energy consumption, population density, economic activities, etc. In this report, the weighted average between West Bank and Gaza is taken into account. Compared to other MENA countries (see chart below), Palestine has the third fast growing population over 2000-2012. It is important to take this into account when establishing the demand forecasts for the 2020-2030 timeframe. (Source: Ref-18 RCREEE and UN data) Forecasts indicate a rapid growth of the population within Palestine at an annual growth rate of 2.9%, which is expected to increase the population from 4.5 M in 2014 to 5.1 M inhabitants in 2020 and 6.4 M in 2030 (see Figure below). The percentage of the urban population should move from 74.1% (2010) up to 78.8% (2030 estimate). Usages of electricity are not exactly the same for the two types of population (individual houses vs small buildings, street lighting). 12 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: Ref-5 World Population Prospects (2015 revision) – United Nations and Ref-6 World Urbanization prospects (2014 revision) – United Nations) The Palestinian economy has been growing moderately and its GDP increased by 2.2% between 2012 and 2013 reaching US$ 7.477 billion. Among other MENA countries, Palestine has the lowest GDP value but with the highest economic growth rate (see figure below). (Source: World Bank data) However, taking into account an important population growth rate and a less important economic growth rate during 2013 (see figure below), GDP per capita has been mechanically slightly decreasing between 2012 and 2013 (US$ 2,329 / capita4). This may influence future investments of households in EE actions. 4 The average income per capita in the MENA region is estimated by World bank to around $3940/capita in 2012 13 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: Ref-8 Palestine 2014 book 2093 - PCBS) As in the other non-oil countries, the structure of the Palestinian economy reveals the important place of the services (58%) and, as a consequence, the relatively modest role of agriculture and industry (see chart below). As a consequence the EE Action Plan related to the economic sectors will be more focused on services and administrations. (Source: World Bank data) Key Indicators for Palestine (2013 data5) To be efficient, EE actions need to be monitored. These indicators are used to verify that the expected benefits are really obtained. The values given in this section are for 2013. These indicators are based on data collected by the Palestinian Central Bureau of Statistics (PCBS). Equivalent snapshots should be prepared during the implementation of the NEEAP 2020-2030. 5 Source: PCBS 14 Energy Efficiency Action Plan for 2020-2030 – Final Report Primary energy intensity: is the ratio between the total energy consumption and the Gross Domestic Product (GDP). It measures the total amount of energy necessary to generate one unit of GDP. At exchange rate: 63,121 TJ / 7.477 G$ = 8.442 kJ / US$. This positions Palestine at the first rank of the MENA countries (see below). The main reason is the relatively low consumption of energy of the service sector. However, it should be noted that the suppressed demand (in particular for Gaza) due to the lack of energy supply creates an artificially low level for this indicator. (Source: Ref-18 EE indicators in RCREEE countries) Final energy intensity: is the ratio of final energy consumption over GDP. The final energy consumption is the energy consumed in industry, transport, households, services and agriculture; it excludes non-energy uses. At exchange rate: 52,375 TJ / 7.477 G$ = 7.000 kJ / $. Energy consumption per capita: is the ratio of final energy consumption over the number of inhabitants. 52,375 TJ / 4.550 M = 11.511 GJ Electricity intensity: is the ratio of final electricity consumption over GDP. The electricity intensity is the electricity consumed in industry, transport, households, services and agriculture. At exchange rate: 4743 GWh / 7.477 G$ = 634 kWh / k$. Electricity consumption per capita: is the ratio of electricity consumption over the number of inhabitants. 4743 GWh / 4.550 M = 1.042 MWh Energy use per household: the unit consumption per dwelling relates the energy consumption of the household sector to the number of permanently occupied dwellings. 24,517 TJ / 875 k HH = 28.019 GJ. 15 Energy Efficiency Action Plan for 2020-2030 – Final Report Electricity use per household: the unit consumption for electricity per dwelling relates the electricity consumption of the household sector to the number of permanently occupied dwellings. 32136 GWh / 875 k HH = 3.672 MWh / dwelling. This average consumption is in the middle range of the household consumptions in the other MENA countries (see chart below – annual consumption per dwelling). The access to electricity, which is available for 99% of the Palestinian population, does not artificially influence this indicator. (Source: Ref-18 EE indicators in RCREEE countries) 3.2. Primary energy supply and consumption The Energy balance of Palestine in Tera Joules for 2013 is given by the table below. 6 Source: Ref-7 Households energy 2015 book (PCBS) 16 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: Energy balance for Palestine 2013 – PCBS) The Palestinian Energy Balance shows several features of the country’s energy system that deserve to be highlighted:  Complete dependence on imported energy products.  Electricity does represent 33% of the final consumption of energy. Annual consumption of electricity represents 10% of GDP7. Any effort to reduce consumption of electricity will have a significant effect on GDP.  Electricity losses are technical losses or energy produced but not consumed (transmission and distribution grids).  For each source of energy, there is one sector in the economy that dominates consumption (see figure below). 7 Total costs including residential sector, based on an average cost of electricity (US$ 0.15 / kWh) and without taken into account the fixed costs in the tariff (connection to the grid). 17 Energy Efficiency Action Plan for 2020-2030 – Final Report (Consumption of final energy per sector – 2013 World Bank own elaboration based on PCBS data) Among the other MENA countries, Palestinian residential sector is the highest consumption segment of final energy (see figure below). (Source: Ref-18 EE indicators in RCREEE countries) Despite high penetration of solar water heaters in Palestinian households (56%), solar thermal energy represents only a small fraction of the Palestinian Energy mix (8%)”. There is a potential to develop this renewable source of energy for both the residential and service sectors. See figure below. 18 Energy Efficiency Action Plan for 2020-2030 – Final Report (Consumption per type of energy – 2013 World Bank own elaboration based on PCBS data) Among the MENA countries, Palestine had the highest demand growth of primary energy over 2000- 2012 (see chart below). (Source: Ref-18 RCREEE data) Because of the weight of electricity in the Palestinian Energy Mix, an EE Action Plan focusing on actions to reduce the consumption of electricity in the residential sector (66% of the total consumption) would have a large impact on final consumption. Additional analysis is recommended to explore potential EE gains in the transport sector for diesel and gasoline. 19 Energy Efficiency Action Plan for 2020-2030 – Final Report Solar energy (thermal) is used only by residential customers. Commercial, public services and commercial sector should benefit from this renewable source of energy (e.g. hotels, swimming and gym facilities, and factories). Losses represent a significant part of the imports that is not offered for sale. Losses are defined as the difference between the total energy supplied (imported or locally produced) and the energy consumption. According to the figure below, the electricity is the energy source which is the most concerned. Solar Gasoline diesel electricity Total energy Relative losses (%) 50% 0,8% 0,3% 11% 7% (Source: World Bank own elaboration based on Energy balance for Palestine 20138) NB-1: energy solar losses come from the lack of efficiency of the solar water heater and the losses in the distribution of water. PCBS estimates these losses around 50%. NB-2: electricity losses are technical losses only. According to other sources9, the global electricity losses for transmission and distribution are significantly higher (20% for 2010). 3.3. Electricity sector The electricity sector is characterized by a heavy dependency upon imports (89% - 201310) from Israel, Egypt and Jordan. Almost all the population has access to electricity: 93% for rural population and 99% for urban population11. It should be noted however that if households in the West Bank have a 24 hour access to power, the daily power service for 97% of Gaza’s households is barely 16 hours. Because of the weight of the residential sector, this EE action plan will focus on the totality of the population. As a consequence, some proposed EE actions may be more difficult to implement for Gaza when energy is not available (e.g. lighting). It should be noted also that supply is not always sufficient to cover the needs (cf. Gaza Strip in particular) and that these needs are growing rapidly (5-7% / year). It is difficult to build EE action on the suppressed demand. However, all the energy which will be saved could be made available for other usages. The yearly energy consumption of the productive sectors represents 3% of the Palestinian GDP12. As a consequence, all EE action leading to reduce consumption is an opportunity for making energy available for other usages and thus reducing the need to increase generation capacity. 3.3.1. Description of the value chain Table below gives the total annual energy purchased in 2013 (imports from IEC and local generation from Gaza Power Plant). It shows two demand peaks (August and January). 8 Energy balance for Palestine is published by PCBS. 9 Sources : NEEAP 2012-2014 and DISCOs 10 According to Energy balance of Palestine for 2013, imports of electricity = 17,043 TJ and local generation (transformation / electricity plants) = 1922 TJ. 11 Source : WB, 2012 12 According to “Economic survey 2014 book 2155 - Palestinian Central Bureau of Statistics”, the total cost of electricity consumed by all sectors for the production of goods and services in Palestine is : 224,973 k$ (page 45). The GDP for 1014 is : 6.9 G$ (source: Palestinian Monetary Authority). 20 Energy Efficiency Action Plan for 2020-2030 – Final Report Energy imported or locally generated (MWh) for Palestine in 2013 Local Imports production Total Israel Electric Gaza Power Month Egypt Jordan Total Corporation Plant January 424,608 16,100 3,509 444,217 51,911 496,128 February 386,187 16,300 448 402,935 39,749 442,684 March 363,917 16,424 - 380,341 34,317 414,658 April 357,532 17,088 312 374,932 32,543 407,475 May 362,508 17,302 - 379,810 32,968 412,778 June 352,135 17,475 234 369,844 39,901 409,745 July 360,144 17,621 12,102 389,867 47,2 437,067 August 381,427 17,747 14,821 413,995 45,806 459,801 September 376,187 17,857 1,128 395,172 30,366 425,538 October 356,427 17,957 1,071 375,455 26,691 402,146 November 380,230 18,046 - 398,276 0 398,276 December 383,506 18,128 7,776 409,410 21,155 430,565 Total 4,484,808 208,045 41,401 4,734,254 402,607 5,136,861 (Source: World Bank own elaboration based on DISCOs data) For Gaza, generation (through the GPP) is limited to a fuel oil power plant in the Strip providing less than one third of the needed supply. This power plant is run at half its capacity. Generation costs are quite high (0.35 – 0.40 $ / kWh for GPP). The West Bank is totally dependent upon imports (IEC for 95% and Jordan for the rest) since there is almost no local generation (however, PV projects are being prepared for the next future). Globally for Gaza and West Bank, the main part of electricity generation comes from IEC (89%) and to a lesser extend from Egypt and Jordan (4%). The power plant in Gaza satisfies around 7% of the consumption The transmission system is quite limited (a few 161 kV segments closed to HV substations for West Bank and one 225 kV segment for Gaza). The distribution grid can be seen as an extension of the IEC grid (numerous 33 kV feeders). Technical losses are mainly located on this part of the distribution grid because of the saturation of the MV segments. For the EE action plan, the reduction of these technical losses is an important area of improvement. Supply of their clients, operation and maintenance of their distribution grids are the main activities of distribution companies (DISCOs). A few municipalities have not yet been consolidated within these DISCos. The table below summarizes the main characteristics of these distribution companies. 21 Energy Efficiency Action Plan for 2020-2030 – Final Report Energy Capacity of Losses / Distribution company # clients purchase import (MVA) purchase (MWh/month NEDCo 80 000 35 000 108 17% TEDCO 20 000 7 000 - 16% SELCo 25 000 7 000 13 39% HEPCo 39 000 30 000 89 22% JDECo 234 000 150 000 500 28% GEDCO 212 000 75 000 - 30% Municipalities 63 000 63 000 - - (Source: PERC 2011 annual report, WB Assessment and action plan to improve payment for electricity services in the Palestinian Territories) 3.3.2. Electricity usages Two third of the electricity produced is consumed by the residential sector13. See figure below. (Source: World Bank own elaboration based on data from Energy balance for Palestine - 2013 The usages for the residential sector (households) are described by the table below. Households % HH by usage 99,5% 49,1% 99,7% 82,0% 99,9% 97,8% 96,9% 15,4% 45,0% 97,1% Energy main Water Desktop Cooking Baking Heating Lighting Washing Fridge Video TV set sources heating computer Kerosene 1,2% solar 3,0% LPG 92,0% 13,6% 27,8% 25,4% Wood 5,2% 29,7% 8,6% 29,2% Electricity 1,4% 48,7% 59,5% 39,4% 100,0% 100,0% 100,0% 100,0% 100,0% 100,0% (Source: data from Yearbook 2014 (Ref-8) and Household survey (Ref-16) 13 2013 data 22 Energy Efficiency Action Plan for 2020-2030 – Final Report The use of energy for cooking, water heating, lighting, washing and fridge is almost common for all households (97-99% of the households). NB: Several sources of energy may be used for a given usage (heating for instance); only the main source has been taken into account in the above table. According the Households energy 2015 book14 solar water heaters are present for 56.5% of the households. However, only 30.7% are currently using it. (They were 66.9% in 2012 to have solar heaters). NB: only 3% of the households consider solar as the main source of energy to heat water (LPG and mainly electricity are used instead. See table above). However, this intensive use of solar water heaters makes Palestine the first MENA country for the use of this renewable energy (see chart below) far before Jordan. (Source: Ref-17 EE indicators in RCREEE countries) According to PCBS data15, average monthly consumption of electricity per household is 306 kWh (January 2015). This values has been taken as a reference for building the residential profile of consumption. 3.3.3. Transmission and distribution losses Technical and non-technical (i.e. commercial, frauds) losses are often not identified separately. The actions needed to reduce these losses have to be specific for each type of loss. For instance, to reduce technical losses which are caused by overcharging pieces of grid equipment (lines, transformers), the solution is generally an upgrade or a reduction of the line length. Other solutions may consist in shaving the peak loads or asking for the implementation of distributed generation. Finally, the design and the negotiation with IEC of an interface, at the transmission level only, would provide Palestine with almost an unconstraint distribution grid. For commercial losses and frauds, the deployment of smart meters may help to locate where to act (penalties, disconnect customers). The cost of the actions is generally less than building a new grid infrastructure. 14 Source: Ref-7 Households energy 2015 15 Source: Ref-7 Households energy 2015 23 Energy Efficiency Action Plan for 2020-2030 – Final Report Figure below gives a history of the losses (technical and non-technical for each distribution company. (Source: World Bank elaboration based on data from PERC and DISCOs) 3.3.4. Electricity tariffs The variable part of the tariff, for each type of client is given by the table below. Palestinian DISCOs purchase power from IEC at a tariff applied to its Israeli end customers. In the framework of the reform of its electricity sector, the Palestinian Authority created a single buyer of electricity, the Palestinian Electricity Transmission Company (PETL), which will be in charge of purchasing power from all sources, including IEC. PETL and IEC are having on-going negotiations on a commercial agreement, which would include a lower wholesale tariff for power imported through four new High-Voltage substations financed by the European Investment Bank and build by IEC in Jenin, Nablus, Hebron and Ramallah. It should be noted that for a given class of customers, the tariff is uniform16. 16 DISCOs have to face different distribution costs because of the repartition of areas “C” in their territory and because of the type of connection with IEC grid (MV or LV point). 24 Energy Efficiency Action Plan for 2020-2030 – Final Report Tariff Price Sector (kWh / month) (NIS/kWh) Residential Palestine except Jericho and Jordan valley At maximum consumption 100 kWh 0.4751 From 101 – 200 kWh 0.5234 More than 200 kWh 0.5487 Pre-paid meter (at maximum consumption 100 kWh) 0.4751 Pre-paid meter (at maximum consumption 200 kWh) 0.5234 Pre-paid meter (more than 200 kWh) 0.5487 Jericho and Jordan valley At maximum consumption 500 kWh 0.3596 More than 500 kWh 0.4176 Commercial Post-paid 0.5899 Pre-paid meter 0.5794 Industrial and MV users Industrial (LV) Post-paid 0.4954 Industrial MV (6.6, 11, 33 kV) Post-paid 0.4560 Water pumping Post-paid 0.5359 Agriculture Post-paid 0.4750 Street lighting Post-paid 0.4735 Temporary Services Post-paid 0.7616 Pre-paid meter 0.7616 (Source: data from PERC Annual report - 2011) It has to be noted that pre-paid meters for residential customers don’t give them any financial advantage: tariff is exactly the same for post-paid and pre-paid while a NIS 0.01 / kWh reduction is offered to commercial clients. As of January 2015, 41.7% of the households have a pre-paid meter17. The fixed component of the tariff, for all clients except those connected to the Jordanian grid, is given below. 17 Source: ref-7 Households Energy 2015 Book 2134 – PCBS 25 Energy Efficiency Action Plan for 2020-2030 – Final Report Sector Fixed cost (NIS / month) Residential Post-paid 10 Pre-paid 0 Commercial Post-paid 20 Pre-paid 10 Industrial LV post-paid 30 MV 120 Agricultural Post-paid 10 Water pumping Post-paid 30 Street lighting Post-paid 10 Temporary Serices Post-paid 20 Pre-paid 10 (Source: data from PERC Annual report - 2011) Power factor18 is a measure of how efficiently the load current is being converted into useful work by a motor, air conditioning, fluorescent lights or any other appliance. It is also a good indicator of the effect of the load current on the efficiency of the supply installations (generators, distribution grid). Clients consume (and pay for) kW but DISCOs deliver kVA. When the devices used by clients have a bad power factor (<1), Utilities will need to produce more kVA. In addition, this situation creates difficulties for voltage regulation and generates technical losses in the grid that may lead to oversize installations. Power factor, if less than 0.92 may lead to financial penalties according to the table below. Power Factor Monthly Penalties ≤ 0.92 0 < 0.92 – 0.7 0.77% from monthly bill for each 0.01 from less than 0.92 PF < 0.7 – 0.6 0.95% from monthly bill for each 0.01 from less than 0.92 PF (Source: data from PERC Annual report - 2011) The two main issues raised by the power factor are: 1- is the measure of kVA by DISCOs accurate enough and are penalties really applied, 2- what are the technical standards required to impose the use of products with a good power factor or the use of correction equipment. Corrective actions should take place in an EE action plan, in particular for air-conditioning systems which are widely used in Palestine during summer. Compared to other MENA countries, the share of electricity in Palestinian household expenditure is the highest (see chart below). As already mentioned, the high cost of electricity bought from IEC explains this situation. 18 Ratio kW (active power) / kVA (Apparent power) 26 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: Ref-18 RCREEE data) 3.3.5. Demand forecasting for electricity PENRA published in 2009 the demand forecasts for 2007-2030 on a directorate basis. These forecasts are based on historical data (2006 and before). Figure below according to this study gives the forecasted evolution of the demand for electricity (medium growth scenario for energy and peak load). (Source: World Bank own elaboration based on Ref-2 Forecasted Demand Study – PENRA 2009) Yearly demand growth for energy is about 6% over the period. It should be noted that this forecast has not been re-actualized with real consumption for 2007-2014. As a consequence, forecasted values for 2030 do not take into account actual restrictions on import and generation which delay the economic 27 Energy Efficiency Action Plan for 2020-2030 – Final Report development of the country. In order to realign these demand forecasts with the actual demand, a specific methodology19 has been developed for this report, splitting demand growth rate in:  Demand growth rate due to the economic development (based on GDP forecasts) and,  Demand growth rate due to the population increase. 3.4. Existing EE programs and preliminary results 3.4.1. Targets defined by the National Energy Efficiency Action plan for 2012-2020 The National Energy Efficiency Action Plan for 2012-2020 (Ref-1) has been decided by the Palestinian Energy Authority (PEA). This plan is structured into three successive phases. Target Supply Cumulated Phase I Phase II Phase III Sectors savings in 2012-2014 2015-2017 2018-2020 2020 (GWh) (GWh) (GWh) (GWh) Industrial 5 6 8 19 Buildings 38 130 195 363 Water pumping - 1 1 2 Total (GWh) 43 137 204 384 (Source: Ref-1 Palestinian National Energy Efficiency Action Plan NEEAP 2012-2020) Total expected savings (384 GWh) during 2012-2020 period of time do represent 5% of the annual consumption in 2020. Gaza Strip20 contribution is close to 100 GWh. Phase I should lead to save 0.8% of the total supply of electricity for 2010. In addition, according to NEEAP 2012-2020, grid losses should be reduced from 20% in 2010 to 16% in 2020. The investment cost to reduce losses has not been materialized in NEEAP 2012-2020 report. It should be noted that, during this 2012 – 2020 period of time, consumption should grow significantly in parallel. The table below compares the savings with the growth of the demand for the 2010 – 2020 timeframe. 19 See Section 4 20 Gaza Strip represents 37% of the total population. 28 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: World Bank own elaboration based on PCBS data from NEEAP 2012-2020) The Energy Efficiency Action Plan for 2020-2030 proposes more ambitious targets by focusing on the most intensive activities21. The Action Plan22 provides a menu of activities from which Palestinian Authorities will be able to select the most efficient actions for Palestine taking into account the investment costs and the benefits of each MWh saved. By 2020, at the end of the current NEEAP, the savings from all the sectors combined will be equivalent to the forecasted reduction of the distribution grid losses. The evaluation of grid losses for 2010 (950 GWh) and for 2020 (1383 GWh23) according to NEEAP 2012-2020 deals with technical and non- technical losses. Total consumption of electricity in 2013 was 18,837 TJ24. Technical losses are equal to 1,897 TJ, i.e. 10% of the total consumption. Assuming this ratio will be the same in 2020, technical losses will reach 10% of 8,640 GWh25. Non-technical losses for 2020 will be: 1,383 GWh – 864 GWh = 519 GW. The Figure below illustrates the distribution of the expected savings among sectors. 21 See Section 5 22 See Section 7 23 Gaza Strip losses account for 344 GWh. 24 Source : Energy balance for 2013 25 Source : NEEAP for total consumption in 2020 29 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: World Bank own elaboration based on PCBS data from NEEAP 2012-2020) 3.4.2. Review of the Phase I action plan results (2012 – 2014) The table below summarizes the action plan for the Phase I. EE Plan Expected Expected savings Sectors Measures implementation / year (GWh) costs (M$) Industrial Energy audits (10) 2,5 0,03 SWH (1000 m2) 2 0,81 Power factor correction 4 0,07 Commercial & Services Energy audits (6) 10,4 1,168 Street lighting (10,000) 2,7 0,105 EE labels & standards SWH (1000 m2) 4 0,71 Public sector Energy audits (17) 14 0,71 SWH (2000 m2) 8 1,41 Awareness campaigns EE seminars (200) 0,5 0,25 EE workshops (75) 0,5 0,25 EE Labs Testing facilities 1,22 Governmental monitoring of Restriction on imported energy consuming equipments equipments Tax exemption on energy saving equipments Total 48,6 6,733 (Source: World Bank own elaboration based on PCBS data from NEEAP 2012-2020) 30 Energy Efficiency Action Plan for 2020-2030 – Final Report It should be noted that during this Phase, the main savings (59%) come from the energy audits of building and related electric appliances in the commercial and public sectors. The chart below present the benefits of the investments decided for this Phase I. Globally, during this Phase I, the ratio investment costs / benefits is 0.75. In other terms, for each US$ invested, the expected benefit is to save 8.8 kWh (equivalent to US$ 1.3226). . 3.5. Legal framework and key EE players 3.5.1. Overview of existing energy regulation General Electricity Law (Law number 13 for the year 2009) aims at regulating and developing the electricity sector in Palestine and at stimulating the domestic and foreign investments in the electricity sector to provide adequate electricity supply at the lowest prices. It provides for establishing a national transmission company (PETL), and it involves a chapter on sanctions against violations. A RE and Energy Efficiency Law has been proposed; the first draft was approved by cabinet in May, 2015. 3.5.2. Presentation of main existing key players The main public stakeholders are the following:  Palestinian Electricity Regulatory Council (PERC): In order to regulate the electricity sector, PERC was established in February, 2012. Among its main functions, PERC has to: 1- review, determine & recommend tariffs, 2- review & provide recommendations on licenses, 3- monitor and enforce licensees’ performance, 4- resolve disputes among stakeholders of the sector, 5- disseminate information and educate consumers.  Palestinian Energy and Natural Resources Authority (PENRA) – former PEA: has been established in 1995. PENRA has in charge the development of the institutional energy 26 Average cost of electricity: US$ 0.15 / kWh. 31 Energy Efficiency Action Plan for 2020-2030 – Final Report framework. This includes overall sector coordination, policy formation, system development, generation, transmission, distribution, tariffs and regulation.  Palestinian Electricity Transmission Company Limited (PETL) -Government owned company: is involved from the source to distribution companies and final consumers, as well as importing/exporting electricity. PETL owns, operates and develops the transmission grid. Within the single buyer model, PETL is the purchaser of power generated from projects with capacity higher than 1MW. Payment of purchased power will is granted by government.  Distribution Companies (DISCos): Population in Palestine receive electricity from 6 distribution companies (NEDCo, TEDCo, JDECo, HEPCo, SELCo in the West Bank and GEDCo in Gaza), in addition to the municipalities / local councils not affiliated with any distribution company. Three of these companies have the legal form of joint stock private companies, while the other three (Southern Electricity Company, Hebron Electric Power Company and Tubas District Electricity Company) still work informally without proper registration at competent departments. Meanwhile, 316 councils (49% of total local councils) have already joined the DISCOs.  Palestinian Energy and Environment Research Center (PEC): PEC is the national R&D institution, established in 1993. It is responsible for studies and promotion of energy conservation, and renewable energy in Palestine. PEC develops and implements national programs for energy conservation, rational use of energy, and implement national programs for utilisation of renewable energy.  Palestinian Electricity Regulatory Council (PERC): PERC insure that customers of regulated utilities receive safe, adequate and reliable service at just and reasonable rates, matching interests between customers and companies working in the electricity sector on the basis of justice. Also PERC fosters competition where appropriate. The council executes electricity sector regulations with accuracy and efficiency that is based on transparency, justice and openness.  Energy Efficiency Unit (EEU): established by PEA, the main missions of the EEU are: 1- identify, analyse and propose possible technical and cost effective policies and measures for EE improvements regarding the generation as well as the consumption aspects, 2- encourage and promote activities targeting EE actions and reducing negative environmental influence caused by energy conversions within both generation and consumption processes. 32 Energy Efficiency Action Plan for 2020-2030 – Final Report 4. FORECASTED DEMAND OF ELECTRICITY FOR 2020-2030 TIMEFRAME 4.1. Methodology and main assumptions Usually, a regression analysis is made on historical data in order to identify a correlation factor between: 1- population growth rate and consumption of electricity, 2- GDP growth rate and consumption of electricity. This approach has not been used here because of the number of disruptions in the time series. In addition, for the action plan, the global growth rate of the demand of electricity is not very pertinent for targeting specific EE actions. As a consequence, and in order to identify separately, the part of the demand coming from the residential sector and the part coming from the commercial/industrial sector, an ad hoc methodology has been used instead. The chart below summarized this methodology. From 2009 and beyond, demand growth for electricity has been taken from the forecasts established by PENRA in 2009. For 2013, these forecasts have been reset to take into account the actual consumption. Then, in 2020, it has been assumed that the NEEAP 2012-2020 will deliver the expected reduction of consumption. So that for 2020, we have a forecasted demand (GWh) which is split between the residential sector and the productive sectors. For the 2020-2030 timeframe, two separate growth rates have been adopted: one for the residential sector based on the population growth (UN forecasts) and another one for the productive sectors based on GDP growth. More details on the assumptions made for this timeframe are given below.  Demand growth rate for 2013-2020 is supposed to be aligned with PENRA study, i.e. between 5.3 and 6.0 % per year  Demand growth for the residential sector is based the UN world population prospects27, total Palestinian population should grow by 2.33% over 2020-2025 and by 2.12% over 2025-2030. According to the UN forecasts, Palestinian urban population growth rate should be twice the rate for rural population28. This will have an influence on particular usages (street lighting, new buildings). 27 Sources : Ref-5 World population prospects (2015 revision) UN and Ref-6 World urbanization prospects (2014 revision) UN 28 Source Ref-6 World urbanization prospects (2014 revision) UN 33 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: World Bank own elaboration based on data from Ref-6 World Urbanization prospects - 2014 revision – United Nations)  GDP growth has been taken as being an intermediate scenario between the optimistic scenario (10.9%) and the baseline scenario (-3,2%) as defined by the Palestine Monetary Authority (PMA)29. In that spirit, the average GDP growth between 2005 and 2014 has been taken close to 4,5% and will be used for the 2020-2030 forecasts30. (Source: World Bank data - pse_country 2015)  Total national demand for electricity in 2013 has been 5270 GWh, including T&D losses31. This value has been used to reinitialize PENRA demand forecasts done in 2009 and adopted as being the new forecast for 2020 (1st year of the 2020-2030 timeframe).  Demand forecasts for residential sector over 2020-2025 time frame has been based on the population growth. Even if in the MENA region, demand growth for electricity is much higher than population growth (because of new usages and a probably with less EE). 29 Source: Ref-14 Economic forecast report - 2014 30 Source: Ref-13 World bank data (pse country – 2015) 31 Source: PCBS Energy balance of Palestine (2013) 34 Energy Efficiency Action Plan for 2020-2030 – Final Report  Losses (technical +commercial) have been estimated between 20 and 30% by Discos. Since EE actions should be effective for the 2020-2030 timeframe, for paid and also for non-paid energy, a 10% ratio has been taken for the estimation of remaining technical losses which are proportional to the total consumption. This is a very conservative value compared to other MENA countries.  Total NEEAP 2012-2020 savings are supposed to be effectively obtained in their totality during the period. It is assumed that these savings will be equally spread over this 9-year period. As a consequence, demand forecasts for 2020 will take into account a reduction of: o Industry: 19/9 = 2.1 GWh o Buildings (commercial & residential): 363/9 = 40.3 GWh (1/3 for commercial and public, 2/3 for residential) o Water pumping: 2/9 = 0.2 GWh o Distribution losses (TL + CL) are supposed to be reduced from 20% (2010) to 16% (2020): 431 GWh  Mutatis mutandis, segmentation of usages (see next section) is assumed to be almost the same until 2020. In other words, sectors of activity should keep the relative weight they have today. It is also supposed that these segments will not evolve during 2020-2030 period except for taking into account the effects of the proposed EE action plan. o NB: A more focused analysis would require analysing consumption trends by sector (e.g. ineffectiveness of policies within the sector, structural changes within the sector, specific economic growth, low fuel price, etc.) 4.2. Segmentation of the consumption of electricity by economic activity In order to identify the potential savings, it is necessary to analyse the sectors of activity where electricity is used to produce value (GDP). The search for efficiency could be then focused on the most electricity intensive activities. Unfortunately, there is no official document segmenting the sectors with their energy consumption. The energy balance of Palestine document (2013) identifies only 5 sectors: agriculture, industry, commerce and public services, residential and grid losses. In order to segment the consumption of these sectors, the following methodology has been adopted:  Use of the official definition of Palestinian economical activities32,  Use of the electricity expenses for producing value (GDP) as a segmentation key (% of total consumption per activity),  Public services (Administration, municipalities and public Agencies) are supposed to be included in commercial and service activities since there is no statistical data available for them. The figure below presents the economic segmentation and the resulting associated consumption of electricity for 2013. It identifies in particular the activities having a high level of consumption. These activities will be considered as the priority for the EE action plan. 32 Source: Ref-15 Economic survey 2014 book 2155 published by the Palestinian Central Bureau of Statistics 35 Energy Efficiency Action Plan for 2020-2030 – Final Report (Source: World Bank own elaboration based on Ref-15 Economic survey 2014 book 2155) NB: the 10th sector - residential sector - is segmented through the usages of electricity and the behaviour of an “average household”. See next section. 4.3. Segmentation of the usages of electricity It is not sufficient to identify electricity intensive activities, because reducing consumption may lead to reduce the level of economic activity. In order to avoid that, an additional segmentation of the activities has been used: the segmentation by usage. For instance, when electricity is used for heating in an industrial process, an energy efficiency measure could be to improve the thermic isolation of the process so that less electricity will be consumed to produce exactly the same result. 36 Energy Efficiency Action Plan for 2020-2030 – Final Report With this segmentation by usage it will be possible to identify specific EE actions. The more the segments are detailed, the more the actions can be focused on. Metered consumption is generally not available for this level of detail. A model has been design to take into account existing data gathered from PCBS surveys and from energy audits33. Since the residential sector is about two third of the total consumption, a specific household consumption profile has been modelled. The table below gives a list of possible usages (all sectors) which have been looked at in order to identify possible EE actions. Activities usages Industrial factory Chillers Motors and pumps Compressors Motors, pumps, production lines Air conditioning Elevators Cooling towers Refrigerators Lighting Food factory Motors and pumps Compressors Air conditioning, fans Chillers Refrigerators, freezers Cooling towers Washing machines Elevators Boilers Lighting Pharmaceutical factory Air conditioning, fans Compressors Chillers Motors, pumps, production lines Lighting Plastic factory Compressors Chillers Motors, pumps, production lines Lighting Book and newspaper factory Air conditioning Compressors Motors, pumps, production lines Blower Printers, computers Lighting Agriculture Water pumping 33 Source: Ref-12 Results of energy audits findings, analysis and recommendations (Palestinian Energy Efficiency Team- 2013) 37 Energy Efficiency Action Plan for 2020-2030 – Final Report Building / generic enterprise Electric heaters Water heating Air conditioning, fans Outdoor lighting Indoor lighting Computing and other devices Elevators Motors, pumps Hotels HVAC systems, fans Pumps, ovens, kitchen Landry, elevators Refrigerators, freezers Compressors, other devices Lighting Hospitals (public / private) Air conditioning Washing, irons, driers Sterilization units, oxygen Ovens Refrigerators, freezers, chillers Pumps, compressors Elevators Lighting Building / public service Electric heaters Water heating Air conditioning, fans, chillers Outdoor lighting Indoor lighting Computing and other devices Elevators Motors, pumps Universities, schools Lighting (internal, external) Air Conditioning Computers, printers, faxes Labs Refrigerators Hot and cold drinks machines Office fans, extract fans Pumps Electric heaters Elevators LCD’s, projectors, TV’s Street lighting Households Cooking Baking Heating Water heating Lighting Washing (machine) Fridge 38 Energy Efficiency Action Plan for 2020-2030 – Final Report TV set, video, computing Cooling (Segmentation of usages) Metered consumption is generally not available for this level of detail. A model has been design to take into account existing data gathered from different studies and from energy audits. For the industrial and commercial services, PCBS publishes cost estimations of the energy needed by each sector to contribute to the GDP. These cost estimation have been translated into energy consumed by usage. For the residential sector, which is about two third of the total consumption, a specific household consumption profile has been modelled, based on available data and PCBS surveys dealing with 875,000 households34. To illustrate that, it has been possible to estimate the average consumption for lighting, heating and washing. This split of the total forecasted demand into specific usages has been then used for evaluating EE action benefits. In the example cited above, an EE action could be to replace bulb with CFLs or CFLs with LEDs. If this action was entered in the model, it would reduce the national consumption for the associated usage. 4.3.1. Industrial, commercial and service sectors Energy audits have been carried out by PENRA’s Energy Efficiency Unit (EEU) with the support from the Agence Française de Développement (AFD) and the French Global Environment Facility (FGEF). More than 50 audits have conducted during 2010 and 2011 for various sectors: industry, commercial and public services35. These audits have been used to refine the usages of electricity for the corresponding sectors. These use cases of electricity gave an order of magnitude of the consumption. A summary of these use cases for the industry sector is given below. (Source: World Bank own elaboration based on EEU’s audits - Industry sector data) 34 Ref-7 Households energy 2015 book 2134 (PCBS), Ref-16 Survey Households 2013 – 200 respondents (World bank) 35 Food factory, hospital, book and newspaper factory, pharmaceutical factory, plastic factory, hotel, Ministry of finance, university, etc. 39 Energy Efficiency Action Plan for 2020-2030 – Final Report Consumption associated to the production line usage (in violet) seems to be the most important usage. As a consequence, priority should be given to specific EE actions dealing with this usage: motors, pumps, compressors. For the food factories, however, the use of refrigerators generates the main consumption of electricity. For the commercial and public services sector, the consumption profile is very different (see chart below below). (Source: World Bank own elaboration based on EEU’s audits - Service sector) Lighting and air conditioning are the main usages of electricity. Therefore, EE action should be focused on these usages. 4.3.2. Residential sector As far residential sector is concerned, three main reference documents have been used: Households Energy 2015 Book 213436, Market Survey: Identifying the reasons for unpaid electricity bills in the West Bank and Gaza (2013)37 and a specific household survey38 (300 families have been interviewed on their consumption of energy). PCBS study (Household energy 2015 book 2134) is a survey done during March – May 2015 The sample size is 7,690 households for Palestine level, 6,609 households responded. The purpose of this survey was to collect the number and the type of appliances per household. When several appliances are used, it has been asked which one is primarily used. There is no data about the consumption per usage. Specific household survey During this survey, 300 families have been interviewed about their house / flat, their usages of energy (solar, electricity and gas). As for the PCBS survey, there is no evaluation of the consumption by usage. However, a more detailed inventory of existing appliances has been done. 36 Source: PCBS Ref-7 37 615 questionnaires were administered in 103 localities within 11 governorates. 38 This survey can’t be considered as fully representative of the Palestinian population. It has been used however to detail specific points in the Household 2015 report from PCBS. 40 Energy Efficiency Action Plan for 2020-2030 – Final Report For the present study, the list of the appliances used by household has been built on these two surveys. The table below gives the source of data for each usage. Usages PCBS survey EE survey Choice for the study Monthly consumption (kWh) 306 317 306 Individual house / flat (%) 48/51 62/38 48/51 Electric stove (%) 48.7 (49% HH) 81 48.7 Gas cooking stove (%) 13.6 (49% HH) 91 13.6 Refrigerator (%) 100 (97% HH) 100 100 Dishwasher -cold feed (%) 32 32 Dishwasher -cold and hot feeds (%) 39 39 Washing machine -cold feed (%) 70 70 Washing machine -cold and hot feeds (%) 51 51 Tumble dryer (%) 50 50 TV (%) 100 93 97 Central heating, boiler with radiators (%) 74 LPG room gas heater (%) 25 85 NA for electricity Electric room heaters (%) 29 72 32 Underfloor electric heating (%) 27 Underfloor water heating (%) 16 AC -heat and cool (%) 43 43 AC –cool only (%) 34 Solar water heater (%) 55 (but 31% only 55 31 are in use) Electric water heater –no tank (%) 59 49 49 Electric water heater -with tank 18 18 41 Energy Efficiency Action Plan for 2020-2030 – Final Report Gas water heater –no tank (%) 28 13 NA for electricity Gas water heater –with tank (%) 17 NA for electricity PCBS and EE surveys look very similar. However, the use of gas (LPG) seems to be more important for PCBS than for the EE survey. This information has not been taken into account since the study is dedicated to the usage of electricity. In order to rank each usage of electricity (% of consumption), the two elements which are missing in both the PCBS and EE surveys are the nominal power of each appliance and the time during which these appliances are used. o The nominal power of each appliance (products are almost standard now so that the variance for a given usage is quite small). For instance, a washing machine with one feed accounts for about 2.3 kW; an incandescent bulb for 60 W per room, etc. o The number of hours per day, a given appliance is used. When manufacturers of appliances give an annual consumption, they often base it on “standard usage / number of cycles”. However, for lighting, there is no way to know how many hours lights will be on. Hypotheses have to be made. For heating (January) and cooling (July), it is possible to compare the differential consumption with more neutral months: the differences can then be allocated either to heating or to cooling. These hypotheses may be discussed and challenged. In the future, either an energy audit or the use of multiple smart meters could help to confirm these assumptions. The Excel spreadsheet model which is proposed can easily capture new hypotheses. NB: Refugee Camps are not taken into account in this segmentation. The analysis of these surveys led to describe an average household representative of this sector encompassing 875 000 households (individual houses and flats), as of January 2015. The main characteristics of such household are the following:  For a “standard” household: 5.2 persons are living in 3.4 rooms (housing density: 1.53)  Monthly consumption of electricity: 306 kWh in January 2015 (this consumption is considered as being an average all along the year39)  Households are apartments for 50,7% and individual houses for 47.3% (remaining 2% are for villas and other)  Main usages of electricity are: lighting (99% of HH), room heating (82% among which 39% use electricity as their main source), water heating (58% of HH), heating foods (20%), and baking bread (10%)  Metering: 58.3% HH are post-paid, 41.7% are pre-paid (smart metering seems to be marginal): o 1 meter for 1 family : 68% o 1 meter for 2 families : 19% o 1 meter for 3+ families : 13% 39 Consumption during winter is slightly higher than during summer months (+8%), except for Jericho city (-40%). 42 Energy Efficiency Action Plan for 2020-2030 – Final Report Figure below describes the segmentation of usages which has been modelled for a “standard” household. The split between these usages has been used to identify the nation consumption and the potential for EE actions. This segmentation has been used for the 2020-2030 period. (Model of the consumption profile for a standard household – World Bank own elaboration based on PCBS data for Households energy 2015) It should be noted that water heating is the first usage of electricity mainly because SWH is very often used as pre-heating only. Other usages are more or less totally dependent on electricity (no alternative source). The 2020-2030 action plans will focus on the five most important usages of this residential profile. 4.4. Forecasted demand by usage and potential savings The modelling of the consumption of electricity which has been done for the 2020-2030 period of time proposes the forecasted demand for each sector of economic activity. Based on the segmentation by 43 Energy Efficiency Action Plan for 2020-2030 – Final Report usage, it is possible to identify the total consumption of each usage and thus a potential volume for EE actions. Since the consumption of the residential sector is close to 60% of the total consumption, the usages have been defined more precisely (standard profile for household). For each usage, a review of available technologies and of human behaviours has been done to propose actions reducing consumption. The table below gives the forecasted demand per sector and usage before implementing the 2020-2030 EE action plan (EE model). 44 Energy Efficiency Action Plan for 2020-2030 – Final Report 45 Energy Efficiency Action Plan for 2020-2030 – Final Report (Demand forecasts for 2020-2030) 46 Energy Efficiency Action Plan for 2020-2030 – Final Report 5. 2030 ENERGY EFFICIENCY TARGETS As already stated earlier, this report focused mainly on electricity. The building sector (including residential and services, administration) is the first consumer of electricity (75% of total consumption). As such, this sector needs specific energy efficiency measures such as building insulation, appliances performances improvement (particularly for air conditioning), Solar Water Heater marks and certification development, etc. Distribution losses are also an important consumer (18%). EE measures will contribute to reduce these losses but for the medium-term, more infrastructural actions have to be decided. 5.1. Reduction of consumption of electricity The target which is proposed in this report has to be discussed in particular in front of the cost of the corresponding action plan. It has been set for a reduction of total consumption of electricity, during 2020-2030, of 5%: o Total estimated demand (2021-2030) = 108 000 GWh o 5% savings: ~5 000 GWh (500 GWh / year). This target is more ambitious than the target for NEEAP 2012-2020: 384 GWh (43 GWh / year), but with the experience acquired with the previous plan, it seems reasonable, compared with other countries, to set this value at a high level. NB: This target is a reduction of the level of consumption; it does not take into account the promotion of renewable energies when used to produce electricity (wind, solar). 5.2. Reduction of the CO2 emissions The reduction of the consumption of electricity will reduce, ipso facto, the CO2 emissions. Almost all (90%) the electricity is imported from IEC. Generation, on the Israeli side, has the following energy mix40: Source: Israel Electric Corporation, Strategic Aspects Overview – 2012 40 47 Energy Efficiency Action Plan for 2020-2030 – Final Report  Coal : 36%  Natural gas : 54%  Diesel : 10% Taking into account the specific level of CO2 emission for each fuel41: o Natural gas : 0.549 kg / kWh (1.21 lbs x 0.4536) o Crude oil : 0.771 kg / kWh (1.70 x 0.4536) o Coal : 0.909 kg / kWh the average emission for each kWh produced by IEC is ~ 0.700 kg / kWh. As a consequence, the above target will save 3.5 million tons of CO2 each year. Compared with other MENA countries (see chart below), Palestine CO2 intensity from fuel combustion in 2011 is already rather modest. The reason is the part of electricity which is imported (generation of electricity is generally one of the main source of CO2 emissions). (Source: Ref-18 EE indicators in RCREEE) 41 Source: International Energy Agency 48 Energy Efficiency Action Plan for 2020-2030 – Final Report 6. REVIEW OF KEY CONTRIBUTING TECHNOLOGIES DURING 2020-2030 The selection of appropriate technologies for reducing consumption is the base for the “vertical” measures. This selection has to take into account what will be available and mature for an implementation starting in 2020 and what will be already in place because of a de facto support during 2025-2030. For instance, incandescent bulbs for lighting will probably be very marginal on the market in 202042. So in order not to oversize the benefits of an EE action plan, a clear vision of what will already be the 2020 market is needed. For numerous new technologies (pure electronic products follow another rule), and compared to the previous generations, the price evolution during their life time encompasses three different phases:  Introduction : the start may be 2 to 5 time more expensive than conventional technologies but at the end of this phase, the gap may be reduced to +20%  Deployment : stabilization of the price  Maturity and replacement: very often prices do not go down but new functionalities are added for the same price. Pure electronic components follow another rule43: life time is no more 10 years but rather 2 to 3 years, prices may fall down because of the volume effect and the automatization processes. In a final product, the relative proportion of pure electronic devices will influence the end consumer price. There is a general tendency to increase the role of electronic circuits in the products and to reduce as far as possible the mechanical parts. Technologies which might be affordable in 2020 and beyond are presented in this section with indications on the expected benefits (less consumption) and their additional cost. These indications are independent of the economic sectors except otherwise stated. 6.1. Lighting Many countries already refuse to import incandescent bulbs. Some models (> 60W) are no more available on the EU market since two years. Only halogen bulbs are accepted; they should totally disappear before 2020. Fluorescent and now Compact fluorescent Light are their natural replacement since several years. The later have an electronic ballast to reduce the Joule effect. Consumption has been divided by 4. Price of CFL is significantly lower than for incandescent bulbs because their life time is 3 or 4 time longer. The use of inexpensive reflectors allows reducing the electric consumption for the same usage. LED is the new lighting generation. Compared to CFL, their consumption is dived by 2 or 3. Price is twice the CFL price but life time is also 3 or 4 time longer. By 2020, prices will be similar. Because of the orientation of the high density light flow, installation of LEDs may not be easy for people living all in the same room. The quality of the LED44 has to be severely monitored to avoid products with a too high intensity of the blue colour (“cold white”). Children’s eyes, in particular, may suffer from the high density45 of the light and from an excess of blue which may create difficulties for sleeping46. 42 EU has already excluded this type of product (> 60W) two years ago. As a consequence, manufacturers will stop soon to produce such bulbs. 43 Moore’s law: every 18 month, price is divided by 2 or performances are multiplied by 2. 44 Several medical studies report negative impacts of high intensity white (cold) LEDs on the retina of children. Main lessons are: don’t use high intensity lights close to e yes, avoid direct lighting, prefer warm white colour (with blue colour). 45 Luminance > 10 000 cd/m² 46 Reduction of the production of melatonin used for regulating the biological clock. 49 Energy Efficiency Action Plan for 2020-2030 – Final Report Type of light Efficiency (lm / W) Life time (‘000 h) Unit price ratio incandescent 10 - 15 1-2 1 Halogen 15 - 30 1-2 1.2 CFL 50 - 100 4-8 1.8 LED 100 - 150 30 - 40 2.3 The next step will be the integration of an Infra-Red / presence detector in order to switch the light on in a room only when there is somebody inside. Light is switched off automatically when leaving the room. 6.2. Electric motors Such motors are used everywhere: industry, residential sector, transportation, etc. Traditional synchronous / asynchronous engines are now replaced with models controlled with an electronic circuit47. This circuit is used to improve the efficiency of the start/stop phases and control the speed in relation with the load. The benefits of these devices are quite substantial: reduction of the required capacity of the engine, compensation of the reactive power, reduction of the electromagnetic and heat losses, dynamic adaptation to the load, reduced energy costs. In the industry sector, motors can’t be replaced without an energy audit because direct costs may be quite high especially if existing pieces of equipment are not yet amortized. On the consumer side (residential sector), manufacturers are almost all planning such change in their products. The main marketing argument is a lower consumption (dishwasher, washing machine). In 2020 and beyond, this argument will not be new anymore: for the same cost, manufacturer will propose this generation of electric motors as an industry standard. As a consequence, it would be sufficient to impose an EE label for imported products and encourage replacing appliances which are more than 10 year old. This effort on labelling should be done with the NEEAP 2012-2020 so that for the 2020-2030 period of time, market will offer (only) effective solutions for customers willing to replace their appliances. As for the other technologies, the price of such motors in 2015 is higher (+20%) but it should go down in the future. Because of the volume effect, it is anticipated that prices in 2020 will be back at the same level the previous generation is today. 6.3. Room heating and air conditioning The lowest level of monthly consumption is obtained when room heating and air conditioning are not used (falls and autumn): 400 GWh48. In summer, because of the use of AC appliances, consumption raises to 460 GWh per month. In winter, the consumption reaches 496 GWh. If thermal insulation may address both heating and cooling, the switch from electricity to gas (LPG) for room heating would make sense in the future. This should be done not only for renovation in the residential sector, for new buildings (residential, commercial) but also for the industry when boilers are used. The main driver for that switch would be the operating cost. With the following assumptions: 47 e.g. variable voltage frequency (VFD: Variable Frequency Drives). 48 2013 consumption of electricity. 50 Energy Efficiency Action Plan for 2020-2030 – Final Report  Price for LPG (12kg): 62 NIS (5.2 NIS / kg),  1 kg of LPG produces 13.8 kWh, with an efficiency ratio of 90%,  Cost of 1 kWh produced with LPG: ~ 0.419 NIS. and compared to the cost of electricity (USD 0.15 / kWh or NIS 0.58), LPG seems to be less expensive than electricity. However, gas appliances are certainly much more expensive. 6.4. Fridges (residential sector) This type of appliance has mainly two components: a compressor and an isolated cabinet. Compressors should follow the same trend as for the electric motors. More EE compressors will become the new industry standard. As a consequence, the EE labelling is a key measure to be implemented during NEEAP 2012-2020 because it should be avoided to import less efficient appliances that will be used for the next 10 years. Regulation of the second hand market should be considered at this stage. 6.5. Water heating Solar water heaters have been very well developed in the past but their proportion among households is decreasing (66.9% in 2012 and 56.5% in Jan 201549). In addition, a significant proportion is out of order (46% of installed SWH). Repairing these systems is a priority. Electricity is used as the main source for 59.5% of the households. For heating water, the use of electricity is not an efficient usage. Indeed, if the ratio final energy / primary energy is close to 80-90% for gas, it falls to 25% for electricity50. The switch to LPG (or natural gas if available) has thus to be encouraged when there is no more room on the roof. 6.6. Smart homes New devices: smart thermostat, communication and control of home appliances from a smart phone. 6.7. Building renovation and nearly Zero Energy Buildings The energy losses for the building in the residential sector are estimated to be:  30% with the roof,  25% with the external walls, and  15% with windows and doors Insulation of roofs should be the first step to start with. If this renovation is done for 50% of the houses (i.e. 25% of the households) the consumption of electricity used for heating could be reduced by:  For room heating: (496-400 GWh) * 2 month * 25% = 48 GWh / year. As far as AC is considered, the insulation of walls, windows and doors with the use of more efficient appliances could be applied to reduce the electricity consumption. 6.8. Smart metering Smart meters offer direct access to information (display at home, independent of the meter location). In addition, they can be used for demand side management. 49 Ref-7 : Households Energy 2015 book. 50 For producing electricity from gas, this ratio is already 50% (thermodynamics) plus transmission and distribution losses + appliance losses. Electricity should be reserved for the usages where no other energy can replace electricity. 51 Energy Efficiency Action Plan for 2020-2030 – Final Report 6.9. Smart grids One of the expected benefits is to extend the capacity of existing infrastructures thanks to the use of communication and computer-aided equipment. The insertion of distributed renewable energy (PV for instance) is a good solution to reduce distribution losses. 6.10. Miscellaneous Other potential sources of EE can be found in EE process technology and energy management, in efficiency of water pumping or in sewage plants. They have not been considered in this report because of the relatively small impact they have for Palestine. 52 Energy Efficiency Action Plan for 2020-2030 – Final Report 7. ENERGY EFFICIENCY ACTION PLAN FOR 2020-2030 7.1. Global strategy and main assumptions Since electricity consumption by the residential sector accounts for almost two thirds of the national consumption, it is of paramount importance for citizens to take ownership of the proposed NEEAP II to benefit from new technologies and to reduce their bills. Vulnerable consumers should be recognized and protected. Electricity which is not consumed is electricity which does not have to be produced. As a consequence, this plan contributes to reduce the dependence of Palestine on power imports and enhance its energy security. It is also a matter of human behaviour. As long as cost of energy (NIS) and consumption (kWh) are not transparent and easily accessed by consumers, it is difficult to ask them to modify their behaviour. That is the reason why smart meters will play an important role in the information of the consumers51. It is also important for DISCOs to improve the operation of their distribution grids in particular when physical limits are often reached. The progressive introduction of “smart grid” techniques may help to go beyond these limits and delay investments because of the development of real-time communication between equipment. The proposed Action Plan presents a list of interventions with associated costs and benefits52 for each of them. A cost per kWh saved is provided so that it can help to select the most appropriate actions. This plan is mainly focused on the two most intensive consumers of electricity: the residential sector and the distribution grid losses. An Excel spreadsheet model has been designed to identify the specific consumption per usage. Among the proposed actions, a selection has been made in order to minimize the cost for end-users and for the Palestinian government. To do that, it is proposed to adopt EU market directives when appropriate for Palestine. This is the case for instance for lighting: traditional bulbs and halogen are no longer imported in Europe above 60W. As a consequence, manufacturers propose now CFLs and LEDs at an affordable price. If the same decision was implemented in Palestine for 2019, the need to subsidy CFLs would disappear. This decision has to be decided during NEEAP 2012-2020 so that the market will be ready in 2020. The proposed Action Plan is structured along three different phases. These phases are not subsequent points in time. They rather correspond to a layer of measures classified according to their complexity as shown below. 51 Real time information is a key element to associate a particular usage and its associated consumption. When a bill is received one month later, it is often impossible to make the link with a particular usage. 52 The list of all the proposed EE actions leads to double the savings targeted in Section 5. That is the reason why a selection within this list has to be made, in particular to take into account their cost and their political and social applicability to West Bank and Gaza. 53 Energy Efficiency Action Plan for 2020-2030 – Final Report The first phase can be considered as a follow-on of NEEAP 2012-2020 Phase III. It is mainly aimed at promoting EE appliances in the residential sector. The second phase is based on a strategic decision - creation of a national electricity market - which is external to this EE action plan. However, if this decision was endorsed, it would help to extend the EE actions beyond the traditional replacement of inefficient energy-using products. In addition, this phase focused on energy conservation (buildings) and demand side management. The third and last phase focuses on the implementation of “smart” appliances or pieces of equipment (smart homes), smart grids and smart cities. Only Phase I is extensively described in this report. Since it should generate benefits already in 2021, it has to be prepared now. The proposed EE target leads to reduce consumption by 5%. The implementation of all the EE actions which are proposed for this Phase I could reduce national consumption by 10%. To take into account the lack of national generation capacity, it might be required to go beyond this target. That is the reason why two other phases are proposed. But they will need time to be matured, in particular because they rely on decisions which go beyond energy efficiency.  Phase I (2021-2030): focus on efficient appliances and industrial equipment. This phase can be viewed as a continuation of NEEAP 2012-2020. Through the information of the consumers, energy audits for the industrial and commercial sectors and financial incitation, this phase aims at the replacement of inefficient energy-using products. Providing consumers with easy access to near real-time and accurate information on consumption and associated costs will be done with the deployment of smart meters and the related information systems. Consumption data will be collected, stored and analysed to provide useful guidance to replace inefficient products and / or improve industrial processes53. This phase will also prepare the third one to ensure that smart home appliances will be fully interoperable in liaison with metering systems.  Phase II (2024-2030): focus on energy market structuring. This phase goes beyond energy efficiency. It should be decided outside the EE action plan because opening the national electricity market to competition serves many other purposes. However, the action plan will take advantage of it through the availability of new market-based services, such as the remuneration of clients reducing their consumption on demand. Low income consumers will find an effective assistance for best practices and direct advice contributing to EE and savings. Thermal insulation of buildings is another focus which should be initiated during the phase. However, the associated activities of renovation may spend over more than one decade. 53 Sub-metering and energy audits are the key tools to be used. 54 Energy Efficiency Action Plan for 2020-2030 – Final Report  Phase III (2027-2030): focus on smart homes, smart buildings and smart grids. The simultaneous use of the market-bases services and smart appliances will enable consumers to become active energy players. For instance, it will be possible to adjust consumption as prices evolve, helping renewable energy intermittency to be managed through demand response actions. These decisions to report or delay consumption during peak hours will avoid to build new generation capacity. All benefits are evaluated in comparison with:  The expected consumption in 2020 before implementing the EE action (base line)  The benefits generated during all the 2020-2030 period (accumulation over 10 years). As a consequence, the cost per kWh saved has been calculated over this 2020-2030 period. When possible, the financing of the actions is left open so that it could be decided to ask the consumers to pay for them, to create a tax, a subsidy. At this stage, it seems important to select the EE actions for their impacts (benefits vs costs). Financing mechanisms could be defined later. 7.2. NEEAP 2020-2030 Phase I (Residential sector) The first phase of the action plan is focused on the residential sector. For each action, a cost / benefit analysis is proposed. The table below summarizes these EE actions with the expected savings during the 2020-2030 timeframe, the total costs and the ratio benefit/cost. When this ratio is less than the price of electricity (US$ 0.13 for residential54), the corresponding investment may be recovered in less than 10 years. Energy Efficiency actions Benefits Total costs C/B (GWh) (US$ (US$/kWh) million) Lighting: move to CFL standard 2,612 1.750 0.001 Lighting: move to LED standard 322 2.275 0.007 Introduction of more efficient fridges 127 4.375 0.035 Switch to gas for room heating 246 24.832 0.101 Electronic thermostats 222 10.177 0.046 Labelling and national campaign 1,270 3 0.002 Repairing of SWH 1,576 126 0.080 Smart metering for all households 1,587 48 0.038 Submetering 317 4.812 0.015 Building thermal insulation 720 345 0.479 Labelling program 881 50 0.057 The annual savings are given by the table below. It should be noted that the total savings for 2020- 2030 are well beyond the target proposed in section 4. This allows the stakeholders to select a sub list of actions taking into account the amount of funding available. 54 This price is based on the tariff for the average consumption of an household (300 Kwh / month): - USD 0.123 for consumption < 100 kWh / month - USD 0.135 for consumption from 101 to 200 kWh / month. - USD 0.142 for consumption > 200 kWh The average tariff is then USD 0.133, which has been rounded to USD 0.13 55 Energy Efficiency Action Plan for 2020-2030 – Final Report 2012- 2020 NEEAP 2020-2030 annual consumption and projected savings (GWh) forecas ts Synthesis for all sectors 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 Total for 2020-2030 Total forecasted consumption (GWh) 8 106,2 8 426,5 8 774,7 9 137,4 9 515,1 9 908,6 10 201,8 10 504,9 10 818,5 11 142,7 11 478,2 108 014 Total savings from the 2020-2030 EE action plan(GWh) 859,3 901,7 946,0 983,5 1 018,4 1 057,7 1 142,8 1 167,9 1 193,6 1 220,0 1 246,9 11 738 Total savings from the 2020-2030 EE action plan(M$) 114,7 120,3 126,2 131,2 135,9 141,1 152,5 155,8 159,3 162,8 166,4 1 566 A detailed description of these EE actions is provided in the following sub sections. 7.2.1.1. Lighting for the residential sector Assumption: it is supposed that the third phase of the NEEAP 2012-2020 plan will lead to the banning of the import of incandescent and halogen bulbs as of January 1st 2019. To do that, it will be necessary to design specific Minimum Efficiency performance Standards (MEPS): CFL will be the new market standard for 2020-2025 and LED the new one for 2026-2030. It is also assumed that the 2012-2020 EEAP led to replace 50% of the traditional bulbs with CFLs in 2020. EE action: as a consequence all new replacement should be done by using CFLs or LEDs. It is assumed that in 2020 population will be forced to replace traditional bulbs55 with CFLs, and then almost 100% of lighting with be done with CFLs in 2021 (time life of bulbs is close to 2 years). In 2026, 50% of the CFLs will be replaced with LEDs. DISCos are required to make the relevant advertising campaigns regarding the replacement of these energy saving bulbs (reduction of the electricity bill of their clients). Costs: because the new market standard will be the CFL, the price of the bulbs is supposed to be unchanged (US$ 1 / CFL bulb), so that almost no public financial incentive would be required. Starting in 2026, cost of LEDs should be around US$ 1.30. Challenge: the challenge for the new decade will be to move from LEDs to Infra-Red detectors for a significant part of the population. This option has not been considered as a priority for this action plan (benefit: 10%, but additional cost: 3 US$ / unit). Savings: yearly savings: 207 GWh for 2021- 2025 and 309 GWh for 2026 - 2030. 7.2.1.2. Use of more efficient fridges for the residential sector Assumption: it is supposed that the NEEAP 2012-2020 led to impose EE labels on all domestic products. It is also supposed that communication and education initiatives have been launched so that consumers are fully capable to read EE labels and compare benefits vs additional costs. This action is supposed to have the priority over the labelling program which is more global. EE action: it is assumed that 10% of fridges56 will be replaced each year with a more efficient model (consumption reduced by 20%). 55 Life time: ~2 years 56 Expected time life is ~10 years 56 Energy Efficiency Action Plan for 2020-2030 – Final Report Costs: as for lighting, manufacturers will progressively introduce more efficient models and remove the less ones57. Compared with today’s prices, there should not be additional cost for the entry models in 2020. However, in order to encourage consumers to move rapidly towards EE products, a subsidy of USD 50 will be offered when destroying a 10 year old fridge and replacing it with a more efficient model. This subsidy would be limited to 10% of the households (87,000) and available during two years only. Challenge: the second hand market with non-efficient products coming from foreign countries is a major risk. Communication and education are key to limit these imports. The obligation to have an EE label on each product is also an important measure to decide. Savings: yearly savings for 2021: 10.1 GWh. 7.2.1.3. Sub metering for families sharing the same meter Assumption: during the households survey58 (2013), it has been noted that 63 families / 3000 where not informed of their own consumption since they shared the meter with other families. An average of 10% has been considered. EE action: additional meters will be distributed behind the global meter to inform the consumers. Costs: total cost is estimated around US$ 4.8 million. Challenge: these families are not seen as individual clients by the DISCOs. The point is not to establish a new contract for them but rather to inform them about their consumption. This is a typical commercial issue to be solved case by case by DISCOs. Savings: yearly savings for 2021: 24 GWh (5% per family). 7.2.1.4. Replacement of electric room heaters with gas systems (residential sector) Assumption: according to the consumption profile (see section 4.3.2), room heater is the second usage by level of consumption. The situation is probably very different for households located near Jericho and Central / North of West Bank. Heating with electricity is probably the usage having the lowest efficiency if one takes into account the primary energy for producing final kWh59. On the other hand, burning LPG may produce heat with 85-90% efficiency. The strategy which is proposed here for individual houses (renovation and new) and new buildings is based on the following priorities: 1. Promote use of Solar Water Heating as far as possible to reduce the consumption of other energies 2. Promote the use of gas (natural gas if available or LPG60) for central heating in order to suppress electric room heaters 3. Keep electric room heaters for very limited usages 57 For this type of appliance in Europe today, only A, A+, A++ and A+++ models are widely available. 58 Source : Ref-16 Survey households – 2013 (300 respondents). 59 The ratio final energy / primary energy is close to 25% (because of generation, transmission and distribution losses). 60 Bottles and external tanks. 57 Energy Efficiency Action Plan for 2020-2030 – Final Report EE action: As a consequence, a national policy is developed to implement the above strategy. It is assumed that all new buildings will provide gas heating and that 2% of existing individual houses61, each year and during 3 years, will move from electricity to SWH and gas. Costs: a USD 1,000 subsidy is proposed for each household willing to move to gas. The annual cost is closed to USD 8.3 million. Challenge: the new place of gas within the energy mix is the central part of the discussion. The use of LPG requires a well-structured distribution infrastructure and security standards to build gas tanks closed to buildings. In addition, LPG is imported from Israel where gas fields don’t contain a high proportion of LPG. The opportunity to implement a natural gas distribution grid in West Bank and Gaza goes beyond this study. Savings: expected savings are 26 GWh the third year. 7.2.1.5. Introduction of programmable electronic thermostats for individual regulation of the temperature Assumption: for electric room heaters, the use of electronic thermostats to adjust the temperature of each room should reduce consumption. Two solutions are available: either to replace electric heaters with a model having such electronic regulation, or to add to the existing installation a centralized thermostat driving individual heaters (3 per household as an average). The second one is recommended for immediate implementation within this EE action plan. EE action: Make sure that electric room heaters with electronic regulation are available on the market. It is assumed that 20% of the households will adopt this device. Costs: USD 180 for an electronic thermostat, US$ 10.2 million for the total cost. Savings: expected savings are 17GWh per year (10% of the consumption per household compared to mechanical thermostats). 7.2.1.6. Communication plan for other electric appliances for residential and commercial sectors Assumption: it is supposed that during 2012-2020 NEEAP, labelling of residential appliances has been defined and that EE cards are available. EE action: Three national campaigns will be organized at the beginning of each phase of the NEEAP 2020-2030. The targets will be the domestic and the commercial sectors for all electric appliances. The key messages will be the labelling, the promotion of EE appliances and the energy conservation behaviours (medias, TV Ads, etc.). The deployment of smart meters for all households and all commercial enterprises will also complete the information of the consumers. A strong cooperation has to be established with DISCOs in order to make sure the consumers will take advantage of the almost real time data delivered by smart meters. In particular, DISCOs should provide their customers with cost comparisons done with similar clients. 61 47.3% of households are individual houses but probably only a part of them use electricity for heating. 58 Energy Efficiency Action Plan for 2020-2030 – Final Report Costs: USD 1 million per campaign in addition to the deployment of about 875,000 smart meters (one per household) in parallel. NB: the cost of the meters (~USD 50 million) is taken into account in the section: reduction of distribution grid losses. Savings: each campaign aims at decreasing the yearly consumption of these two sectors by 2%. As already seen in other countries, this reduction is not sustainable overtime. That is the reason why the national campaigns will be repeated during the 2020-2030 timeframe to maintain a 2% reduction of the consumption. Residential sector: yearly savings for 2021: 97 GWh Commercial / services sectors: yearly savings for 2021: 36 GWh 7.2.1.7. Smart metering for all the residential sector EE action: The deployment of smart meters for each households aims at informing consumers, so that they can act on their consumption. For the DISCOs, this deployment will help to reduce commercial and technical losses. This deployment requires also implementing an advanced information system to monitor losses and provide comparisons between similar clients. The goal is also to enable consumers for detecting extra consumption. Costs: USD 48.1 million for the deployment of about 875,000 smart meters (one per household). Savings: according to similar projects implemented in others countries, the expected reduction of consumption is about 2.5%. In addition, reduction of distribution grid losses should reach at least 2%. Globally, 218 GWh / year could be saved. 7.2.1.8. Building thermal insulation for individual houses Assumption: thermal insulation is important for reducing energy consumption for both heating and cooling. It is generally estimated that the loss of energy in winter may reach 15% for windows and doors, 25% for the external walls and up to 30% for the roof. It is also assumed that in summer, this insulation will reduce AC consumption in the same proportion. EE action: individual houses are targeted for the thermal insulation. Actions should be focused on the replacement of windows and doors and on the insulation of the roof. One third of the individual houses62 are targeted by this action. Costs: cost for insulation an individual house is estimated around US$ 2,500 for reducing the consumption of energy for heating by 25%. Total cost is estimated around US$ 345 million. Savings: based on a reduction of 25% of the electricity consumed for heating, the total savings are around 33 GWh / year. 7.2.1.9. Implementation of labelling program for domestic appliances Assumption: this program has been initiated during NEEAP 2012-2020 with the development of testing facilities. 62 About one household over two leaves in an individual house (source: PCBS household survey). 59 Energy Efficiency Action Plan for 2020-2030 – Final Report EE action: a simplified EE labelling program for domestic appliances is defined. Trainings are organized for professionals, media awareness campaigns are dedicated to the use of the EE cards, laboratories are certified for testing and validating the characteristics of various appliances (fridge, washing machines, HVAC, lighting, …) either imported or locally manufactured. Control mechanisms are defined such as the test of randomly selected samples of domestic products. Costs: US$ 50 million for the first certified laboratory. Savings: 69 MWh / year (8% of the annual consumption of the main domestic appliances). 7.2.1.10. Repairing existing solar water heating systems Assumption: According to households survey for 2014 (PCBS), 25.8% of existing SWH are out of order. It is proposed to repair these installations. This should lead to save 50% of the electricity used producing hot water for an average surface of 1 m2 per household. EE action: repairing out of order installations. Costs: cost is assumed to be similar to the one for a new installation (US$ 700). Total cost is estimated around US$ 126 million. Savings: based on a reduction of 50% of electricity consumed, the total savings are around 121 GWh / year. 7.3. NEEAP 2020-2030 Phase I (other sectors) 7.3.1.1. Sub metering for large enterprises Assumption: for large enterprises and public services, the consumption of electricity is a kind of stranded cost: it is difficult to relate electricity consumption with activities and specific behaviours. This is true in particular for post-paid metering. In addition, for the large organisations, payments and consumption are not managed in an interactive manner. 5% of the 51,000 industrial and commercial enterprises63 representing 238,000 employees should be targeted. EE action: additional (sub) meters will be distributed behind the totalizing meter to inform the manager of various activities (production, sales, administration, R&D…). Ideally, the information provided by sub metering should encompass daily and monthly consumptions so that enterprises will be able to associate efficiency measures with results. In addition, the designation of an “energy manager” in the large enterprises should help to realize where energy is consumed and for what benefit. Costs: total cost is estimated around US$ 5 million (based on 10 sub meters per enterprise at US$ 200 per sub meter). 63 According to Ref-8 statistical yearbook of Palestine 2014: 16,200 industrial enterprises, 500 construction firms, 600 information & communication enterprises and 33,400 service companies. 60 Energy Efficiency Action Plan for 2020-2030 – Final Report Challenge: Disco should be involved in the selection of the “strategic” locations where to install sub metering in order to reflect an objective consumption per activity. Savings: yearly savings for 2021: 6 GWh. 7.3.1.2. Reduction of the distribution losses (part-1) EE action: The deployment of smart meters for each household aims at informing DISCos in real time and at detecting thefts by comparing energy delivered by LV feeders and the total consumption of the related consumers. This deployment requires also implementing an advanced information system to monitor losses. Costs: USD 48.1 million for the deployment of about 875,000 smart meters (one per household). Savings: reduction of distribution grid losses should reach at least 2% or about 100 GWh per year. 7.3.1.3. Reduction of the distribution losses (part-2) A specific action plan needs to be built by DISCos for reducing these losses. Among the most frequent operations to undertake, the following one seems to be the priority, for the part of the distribution grid they manage:  Use state of the art troubleshooting tools to improve maintenance of MV/LV lines  Reduce the length of LV lines by implementing additional MV/LV transformers close to the loads  Increase the detection and the measure of unbalanced loads on 3-phase lines (MV and LV)  Install additional meters on the feeders to detect thefts (difference between the total amount of energy leaving the transformer and the total metered energy on the consumer side)  Organize regularly technical inspections  Make sure that street lighting has a specific meter  Remove all non-metered consumption 7.4. NEEAP 2020-2030 Phase II 7.4.1.1. Demand side management The proposed NEEAP II focuses on energy consumption (not generation). Since Palestine is mainly a consumer importing energy from IEC, the efficient use of energy needs to be the priority. However, in the future, Palestine should become more independent and, as such, will be responsible to manage its domestic generation and in particular the peak demand. For a given annual consumption of energy, the generation costs are not the same if the consumption profile is relatively flat or if this profile has severe peaks of demand. Indeed, a power plant which is used for the peaks only (a few hundreds of hours / year) will have higher operating costs than a power plant used for supplying the base load. In order to shave these peaks of demand and report consumption later, a communication mechanism is needed between the system operator and the consumers. The deployment of smart meters will be the base for this type of communication. Additional mechanisms, such as a ToU (time of use) tariff may help to convince customers to reduce temporarily their consumption. 61 Energy Efficiency Action Plan for 2020-2030 – Final Report The value of this type of service is based on the generation costs which are avoided during a peak demand. 7.4.1.2. Building thermal insulation The short-term action proposed in Phase I is the thermal insulation of existing buildings. For new buildings, it will be necessary to design specific Minimum Efficiency performance Standards (MEPS) and building codes, in order to avoid less efficient a posteriori actions. The concept of nearly Zero Energy Building (nZEB) is an attempt to standardize the consumption of energy per m 2 per year. Building codes for existing and new buildings will have to be revisited in order to introduce this concept of nZEB. This will be mandatory for all public building and subject to a financial incitation for the residential sector. The use of renewable sources of energy has to be considered in order to limit the use of energy “imported” by the buildings. A building renovation strategy needs to be defined for the residential sector in order to improve thermal insulation (starting with the coldest and the hottest regions). 7.5. NEEAP 2020-2030 Phase III In the proposed EE Action Plan, Phase I prepares the “smart homes”. In this phase, the introduction of “communicating” appliances should improve the consumption of energy but the main benefits should have been collected during the previous phases. In addition, the future price for this type of product is not yet stable enough to freeze firm technical orientations. Phase II is the foundation for building smart cities. From a pure energy efficiency perspective, the additional benefits of the communication between components (street lighting, car parks, transportation …) are more related to an optimization of the use of the energy at a more global scale. However, this phase introduce a major breakthrough for the design of distribution grids. 7.5.1.1. Towards the implementation of smart grids Until recently, the 280 connection points from Palestinian electricity distributors with IEC were mostly build at low voltage (LV) with undersized equipment. This is one of the explanations of the high level of technical losses. With the completion and the interconnection of the 4 substations in the West Bank, all these interconnections should be reconsidered. Progressively, all LV connection with IEC should be replaced by a new link to an output feeder of these substations. This reconstruction of the distribution grid will take time. The introduction of smart grid component is a first attempt to build this new architecture. In order to reduce technical losses and to prepare the insertion of distributed generation (PV, wind), the use of this new technology should avoid to implement a new grid with obsolete (traditional) components. The reduction of technical loses is not sufficient to justify the introduction of smart grids. The ability to support RE at the distribution level will remove any barrier for connecting a high proportion of intermittent sources onto the new grid. 7.6. Impacts of this EE action plan on the creation of jobs Potential EE domains may become opportunities for creating new jobs. This has been already demonstrated in several MENA countries (Lebanon, Egypt). For instance, the use of more efficient appliances may create new business opportunities: these appliances could be locally manufactured and not imported. High efficiency lighting is such an 62 Energy Efficiency Action Plan for 2020-2030 – Final Report opportunity with the need to produce CFLs and LEDs. Encouraging the creation of local factories manufacturing these new products should reduce the import costs and create new jobs:  For the manufacturing of bulbs and the final assembly  For the manufacturing of the electronic circuit  For testing and packaging The market size is probably more than 2 million energy saving bulbs (50% of the households, average of 4 bulbs per household). Solar water heating is another source of job creation with the installation of new systems and the maintenance of existing ones. Thermal insulation of buildings is the main source of job creation. According to the review of European NEEAP, 1 Mtoe/year energy savings (11 630 GWh) will enable the creation of 5 000 new jobs mainly in the construction sector, energy certifiers and auditors, inspectors of heating / air conditioning systems. For a target of 5 000 GWh, 2150 jobs could be created in Palestine. Energy Efficiency actions lead to net employment generation given that energy efficiency activity is more labor intensive (and less capital intensive) than the production of energy saved. For building insulation and renovation, a study64 in Europe concluded that about 1 million new jobs related to energy renovations have been created in Europe during the period 2005-2015. Compared to the investment level, this is equivalent to the creation of 12 to 17 new jobs for each €1 million invested. Similarly, bases on this ratio, the NEAAP 2020-2030 which is proposed here for building renovation could lead to create between 3600 and 5100 new jobs in Palestine. According to another study made in Europe65, the employments within EU28 dealing with energy efficiency goods and services sold in 2010 amounted to approximately 1% of total EU employment. A direct comparison with Palestine could lead to 18,000 jobs dedicated to energy efficiency. However, the target accepted by EU (-20%) is more ambitious than the Palestinian one (5%). 7.7. Recommendations for an implementation plan This section provides indications about how to roll-out and implement the energy efficiency included in the action plan. In order to contribute to identify roles and responsibilities, a RACI66 approach is proposed. The table below summarizes the main steps and actions. For all these actions, the PENRA/ Energy efficiency Team has the responsibility to organize the advertising campaigns and to follow up on. For all the actions PEC has the responsibility to propose financial incentives and devise the appropriate business model to each measure. From the table below, the “A” means Accountable, while the “R” means Responsible. 64 Jobs creation through energy renovation of the house stock (Frits Meijer, Henk Visscher, Nico Nieboer, Robert Kroese Neujobs working paper D14.2 – december 2012 65 Assessing the Employment and Social Impact of Energy Efficiency - Final report Volume 1: Main report - Cambridge Econometrics November 2015 66 RACI is a responsibility assignment matrix. 63 Energy Efficiency Action Plan for 2020-2030 – Final Report Actions A R Approval of the NEAAP II target (including PENRA PENRA-EE team required public financing and donors mobilization) Definition and follow up of the EE indicators PENRA-EE team PCBS (consumption by usage, EE action specific measurement) Specify annual objectives for reducing the grid PEC DISCOs losses Banish incandescent lamps PEC Customs Lighting: move to CFL standard PEC for technical DISCOs for standards advertising campaigns, PENRA-EE Team for Consumers communication Lighting: move to LED standard PEC for technical DISCOs for standards advertising campaigns, PENRA-EE Team for Consumers communication Introduction of more efficient fridges PENRA-EE Team for MoF for the subsidy technical standards PENRA-EE Team for PEC for labelling recycling, PEC for proposing Consumers, subsidies Private sector Switch to gas for room heating PENRA for organizing MoF for subsidy, gas access Private sector for EE Team for installation, promoting SWH Municipalities for organizing gas supply Electronic thermostats PENRA-EE Team for Consumers technical standards Labelling and national campaign for all PEC for technical PENRA-EE Team for electric appliances standards communication Repairing of SWH PEC for technical Private sector standards Smart metering for all households PEC for technical DISCOs standards Sub-metering PEC for technical DISCOs, standards Private sector Administration Building thermal insulation PEC for technical Ministry of Public standards and defining Works and Housing incentives Private sector Labelling program for domestic appliances PEC for technical PENRA-EE Team for standards communication, organizing laboratory certification and control mechanisms 64 Energy Efficiency Action Plan for 2020-2030 – Final Report All these actions could be implemented in parallel. For each action, the leader “A” should build a business plan identifying the expected benefits, costs and possible needs for public funding / subsidies. The business plan would include a detailed implementation plan for submission to a NEEAP steering committee composed of senior representatives from PEC, PENRA-EE Team, MoF, DISCOs, municipalities and consumers. The main role of this committee will be to monitor and support implementation of each action and to ensure that implementation delivers the expected results. 8. CONCLUSION The Energy Efficiency Action Plan for 2020-2030 (NEEAP II) for Palestine puts forward additional opportunities for energy efficiency to reach an ambitious target to reduce total electricity consumption by 500 MWh per year. The Action Plan focuses on measures to reduce the consumption of electricity in the residential sector (two thirds of the national consumption) because of its largest savings potential. Indeed, electricity is the main source of energy in the Palestinian energy mix, and for this source, the residential sector is the main consumer. Other energy sources have their own leading consumption sector. Diesel and gasoline are mainly consumed by the transport sector, LPG by the residential sector. These sources might need also a specific EE action plan. The NEEAP II is composed of a layering of three phases: Phase I starts in 2020; Phase II starts in 2023 and Phase III starts in 2026. Phase I of this plan focuses on “low hanging fruits” i.e. the most energy- hungry appliances (lighting, room heating, fridge and HVAC systems). Phase II and III are implemented in parallel with the first one but are delayed by 3 years each. They are dedicated to more complex actions based on the structuring of a national energy market and on the rehabilitation of the distribution grid. It is recommended to already start preparing the implementation of Phase I in order to ensure that energy saving benefits are reaped by 2021. The NEEAP II includes a cost/benefit ratio (US$/kWh) per each proposed action to rank their cost- effectiveness. All actions have pay-back periods of less than ten years, except for the building thermal insulation. The source of funding for these investments is not prescribed since many actions could be financed by the consumers themselves but the introduction of public funding could help accelerate their implementation. Some very efficient actions do not require large investments, such as new regulation, awareness campaigns and improved organization, and could be effective if stakeholders are well identified. This is the case for example for the technical specifications (Minimum Efficiency Performance Standard) used to remove the least energy efficient appliances. For the sake of efficiency, it is recommended to build upon existing high-quality standards and regulations such as those from the European Union (EU), e.g. labelling. Technical specifications could be simplified, but regulatory action should be undertaken as soon as possible to send appropriate signals to market actors (consumers and manufacturers) and attract private capital for required investments. The energy efficiency actions put forward in the Action Plan 2020-2030 have been selected based on a consumption model designed with input data mostly from the Palestinian Central Bureau of Statistics (PCBS) to reflect the part of each usage within the total consumption. In the absence of statistics related to quantitative usages of electricity, a daily consumption profile has been designed. This model has been used to size the EE potential for activity sectors and usages of electricity within each sector but it could be used also in the future to dimension generation capacity on a daily basis. Managing the demand for energy is a priority today but managing the power capacity (peak loads) will become important when an independent transmission grid will be operated by Palestinian Electricity Transmission Company Limited (PETL). At present, Palestinian electricity distributors purchase 65 Energy Efficiency Action Plan for 2020-2030 – Final Report electricity from the Israel Electric Corporation (IEC) at a high price but the latter is responsible for managing the flexibility of the demand. In the future, PETL could purchase “blocks” of electricity on the international market at a lower price, but it will have the responsibility to make daily forecasts and balance demand and generation in real time. To be effective as a system operator, PETL will have to know the consumption and the factors influencing it: external temperature, commercial activities, and consumption behaviours. Among the proposed EE actions in the NEEAP II, two of them may require a complex implementation program:  The first action is the generalization of the smart meters for the residential sector. This program aims at providing relevant information to the consumers so that they will be in a position to better manage their consumption. These meters are the visible part of the iceberg. A sophisticated information system is simultaneously required from DISCos to prepare energy audits per household, compare consumption profiles to detect non-efficient usages, recommend the replacement of appliances, etc. Home displays or equivalent devices (e.g. mobile application) will help the consumers to relate their daily behaviours and the impacts on their consumption. Monthly billing information is not sufficient to create the link between usage and energy. The same program should help DISCOs to improve their quality of service (detection of failures) and reduce technical / commercial losses. However, smart meters are not sufficient. Internal processes have to be implemented to randomly check the consumption and detect unbalanced low-voltage (LV) lines.  The second action is to promote a switch from electricity to gas (LPG and/or natural gas) for room heating. With an efficiency ratio of only 25%, it does not make sense to use electricity to heat air or water from an energy perspective. Electricity should be reserved to usages where there are no replacements (motors, electronics …). For consumers, the main argument in favour of electricity is the low cost of appliances. However, the operational costs of gas are much lower in the long run. This switch cannot be initiated without a national strategy for gas so that the cost of the required infrastructures (transportation and storage of gas) will be shared between all the actors. The development of solar water heating is part of this issue since it would decrease the need to use non-renewable energy. Palestine has been a regional leader in the implementation of solar water heaters, but this position is rapidly being eroded. The action which is proposed suggests starting with repairing the existing systems which are no longer functional. Several of the recommended energy efficiency actions should contribute to create jobs. Job-related benefits are not included the economic analysis. However, international experiences such as in the EU and Lebanon confirm that EE measures in the building sector, i.e. insulation, contribute to create the largest number of jobs, followed by solar water heaters and CFL manufacturing. As for other EE actions proposed in this plan, communication campaigns and technical assistance for market structuring could also contribute to job creation. The success of solar water heaters in Palestine could be a future reference to develop and support the take-off of other local industries: relatively simple components, simple financing mechanisms and acceptable return on investment for the development of thriving companies all along the supply chain. 66 Energy Efficiency Action Plan for 2020-2030 – Final Report 9. REFERENCES 1. The Palestinian National Energy Efficiency Action Plan (NEEAP) 2. Forecasted Demand Study – PENRA (2009) 3. The National Energy Efficiency Action Plan for Lebanon (NEEAP 2011-2015) 4. Annual Report 2011 - PERC 5. World Population Prospects (2015 revision) – United Nations 6. World Urbanization prospects (2014 revision) – United Nations 7. Households Energy 2015 Book 2134 - Palestinian Central Bureau of Statistics 8. Palestine 2014 book 2093 - Palestinian Central Bureau of Statistics 9. Energy Efficiency Indicators Fundamentals on Statistics - IEA (2014) 10. Fiscal Developments: Fourth quarter and Full Year 2014 – Ministry of Finance State of Palestine 11. National Energy Efficiency Economic Model for Palestine (PEA – 2013) 12. Results of Energy Audits Findings, Analysis and recommendations (Palestinian Energy Efficiency Team – 2013) 13. World Bank data (pse_country 2015) 14. Economic Forecast Report, 2014 (PMA – December 2013) 15. Economic survey 2014 book 2155 - Palestinian Central Bureau of Statistics 16. Survey Households 2013 – 300 respondents 17. Survey commercial buildings – 20 buildings / 2674 employees 18. Energy Efficiency Indicators in RCREEE (Regional Center for Renewable Energy and Energy Efficiency) Member states (2014) 67